Re: TC-P50VT20 10 Blink Code
Great, so I'm positive that A board is still alive, will now send SC board for repair (got somone in UK and buffers for double check) and cross my fingers when I will have them back. Will report here.
Thanks for your help!
TC-P50VT20 10 Blink Code
Collapse
X
-
Re: TC-P50VT20 10 Blink Code
yes, 6 blinks it should be, but I had this situation too on a 42gt20.
so... with sc2 and sc20 disconnected or the ss power link disconnected, I had 10 blinks. I had this situation with 2 identical A board, and first time I tought that both of them are bad. but... both of them were almost OK, and after fitting a good sc board the tv worked fine (one A board did not have image.).
get a good sc board and maybe sd or su boards if needed, and give it a shot. with A board separated from D board, the tv should start with full white screen. and... maybe if you disconnect sc2, sc20 and the connection between A and D boards... I did not try this, maybe it will go into 7 blinks... I am curious too. Also, I could try something, because I still have some gt20 boards.
and about your question, I guess 10 blinks is ok.
try to check the buffers, to have no shorts between panel outputs and the 4 power screws.
as for your question, I guess it is ok to turn 10 blinks and have a good A board.Last edited by dj01fad; 07-04-2016, 09:26 AM.Leave a comment:
-
-
Re: TC-P50VT20 10 Blink Code
just want to make sure no other board is broken.
thanks!Leave a comment:
-
Re: TC-P50VT20 10 Blink Code
there's no easy way to describe what to do other than the ribbons are not in straight or all the way.
So, only adjust with the TV off. Take the back off, turn it on , look at the lines and they will ine up with the buffer connector that is wrong, take note or get a marker to put a dot on what is wrong.
Turn it off, lift the latch, gently pull the ribbon out and with two hands get it really even and straight , insert and you can feel it wedge in.
If the latch is really hard to pull down that's usually the first warning it's not right.
The other thing is compare to a good one and often you'll see it's crooked.
The total cost of the repair was about $240 US. And it only took about 5 months to fix.
I'm happy!
Thanks tw2005. I sincerely appreciate it!!Last edited by Katzat; 07-01-2016, 08:59 PM.Leave a comment:
-
Re: TC-P50VT20 10 Blink Code
there's no easy way to describe what to do other than the ribbons are not in straight or all the way.
So, only adjust with the TV off. Take the back off, turn it on , look at the lines and they will ine up with the buffer connector that is wrong, take note or get a marker to put a dot on what is wrong.
Turn it off, lift the latch, gently pull the ribbon out and with two hands get it really even and straight , insert and you can feel it wedge in.
If the latch is really hard to pull down that's usually the first warning it's not right.
The other thing is compare to a good one and often you'll see it's crooked.Leave a comment:
-
Re: TC-P50VT20 10 Blink Code
TW, Sooo....
I sent the SC Board, the SU board, and the SD Board back in to PTS. They found my SD board was fried beyond any repair. SU Board was ok!!!
So they fixed the SC Board, and sold me a refurbished SD board.
I reinstall them, and did the power up test, and ALL IS GOOD.
So I put it all back together, plug it into cable, and I have horizontal lines and bands across the screen. RATS!
Am I correct in assuming this is caused by me not properly seating or aligning the ribbon cables to the SU and SD boards?
I'm asking because I don't want to disassemble this thing again if the problem is the panel. If that's the case, the kids are going to have to learn to read books or something.
Help lm one more time. I think I'm almost there!
So, only adjust with the TV off. Take the back off, turn it on , look at the lines and they will ine up with the buffer connector that is wrong, take note or get a marker to put a dot on what is wrong.
Turn it off, lift the latch, gently pull the ribbon out and with two hands get it really even and straight , insert and you can feel it wedge in.
If the latch is really hard to pull down that's usually the first warning it's not right.
The other thing is compare to a good one and often you'll see it's crooked.Leave a comment:
-
Re: TC-P50VT20 10 Blink Code
You have no choice but to contact PTS. Don't be surprised if they ask you to send your buffers in.
You can always hook the board up first without the buffers and jumper sc50, that way if it blows it takes those other boards out of the equation.
also the SC must be bolted in properly to ensure good earths, don't run it with lots of screws out.
The Vfg bolts in the Sd / Su are removed when performing the sc50 jumper run.
I sent the SC Board, the SU board, and the SD Board back in to PTS. They found my SD board was fried beyond any repair. SU Board was ok!!!
So they fixed the SC Board, and sold me a refurbished SD board.
I reinstall them, and did the power up test, and ALL IS GOOD.
So I put it all back together, plug it into cable, and I have horizontal lines and bands across the screen. RATS!
Am I correct in assuming this is caused by me not properly seating or aligning the ribbon cables to the SU and SD boards?
I'm asking because I don't want to disassemble this thing again if the problem is the panel. If that's the case, the kids are going to have to learn to read books or something.
Help lm one more time. I think I'm almost there!Last edited by Katzat; 06-27-2016, 08:47 PM.Leave a comment:
-
Re: TC-P50VT20 10 Blink Code
disconnected SC2 and SC20 gives me 10 blinks, (same with only sc2 disconnected).Leave a comment:
-
Re: TC-P50VT20 10 Blink Code
Dear all SC board experts,
I had a perfectly running TX-P46VT20E (european version of the TC-P46 13th generation plasma high end 3d model).
This weekend when I powerd up the panel from complete power off ( switch on the side was off) to power on, I heard a pop and saw a little flash (the room was dark) coming from the area where the SC board is sitting.
After this SOS4,
I unplugged SC2 (which is short) and SOS goes to SOS10.
Even unplugging SC20, P11 (so no SS and SC (or buffer) boards running) doesn't change anything on the SOS10!?
So my question is, is only the SC board damaged (P11 reconnected, the LED on SS board is green)? I can try to measure Buffer for shorts (not to blow replacement SC) and get a replacement SC Board (TNPA5081AG), but first I want to know if and how to check for more broken parts on my loved panny plasma.
What would you guess and/or recommend to else check?
thanks so much in advance for your help.
horuck
Blown SC can cause both 4 blink and 10 blinks but disconnecting other things may just be confusing the situation.Leave a comment:
-
Re: TC-P50VT20 10 Blink Code
Dear all SC board experts,
I had a perfectly running TX-P46VT20E (european version of the TC-P46 13th generation plasma high end 3d model).
This weekend when I powerd up the panel from complete power off ( switch on the side was off) to power on, I heard a pop and saw a little flash (the room was dark) coming from the area where the SC board is sitting.
After this SOS4,
I unplugged SC2 (which is short) and SOS goes to SOS10.
Even unplugging SC20, P11 (so no SS and SC (or buffer) boards running) doesn't change anything on the SOS10!?
So my question is, is only the SC board damaged (P11 reconnected, the LED on SS board is green)? I can try to measure Buffer for shorts (not to blow replacement SC) and get a replacement SC Board (TNPA5081AG), but first I want to know if and how to check for more broken parts on my loved panny plasma.
What would you guess and/or recommend to else check?
thanks so much in advance for your help.
horuckLeave a comment:
-
Re: TC-P50VT20 10 Blink Code
You have no choice but to contact PTS. Don't be surprised if they ask you to send your buffers in.
You can always hook the board up first without the buffers and jumper sc50, that way if it blows it takes those other boards out of the equation.
also the SC must be bolted in properly to ensure good earths, don't run it with lots of screws out.
The Vfg bolts in the Sd / Su are removed when performing the sc50 jumper run.Leave a comment:
-
Re: TC-P50VT20 10 Blink Code
You can always hook the board up first without the buffers and jumper sc50, that way if it blows it takes those other boards out of the equation.
also the SC must be bolted in properly to ensure good earths, don't run it with lots of screws out.
The Vfg bolts in the Sd / Su are removed when performing the sc50 jumper run.Leave a comment:
-
Re: TC-P50VT20 10 Blink Code
They were when I was last troubleshooting before sending the SC Board in. I'll do that again tonight.
Assuming they're not shorted, what do you recommend?Leave a comment:
-
Re: TC-P50VT20 10 Blink Code
Were the sd su boards checked for short?Leave a comment:
-
Re: TC-P50VT20 10 Blink Code
Well, I was hoping to report back here that I had a perfectly functional TC-P50VT20. That's not the case.
The SC board arrived back from PTS today, so I put it in and powered the TV. After a few seconds of pressing the power button, I heard an audible "POP" and the set issued the 7 blink code. There was no smoke or any smell of electrical toast. I also couldn't detect any physically blown stuff on any of the boards.
I got the manuals out and found that one refers specifically to the SU/SD boards or the SC board.
So I looked at them again to see if I could find a blown cap or something and found I had forgotten to connect the little ribbon cable between the SU and SD boards (SD11/SU11). I connected this, but I still get the 7 blink code.
So I did the SU and SD Boards Isolation procedure where you disconnect all the connections between the SC and the SU/SD boards and jumper the pins at SC50. According to this procedure (if I'm interpreting it correctly), if the set still issues the 7 blink code under this test, the problem is with the SC board.
My question is does leaving this ribbon cable disconnected between the SU and SD board cause a catastrophic failure of the SC board? What do you recommend now? Should I send the three boards back to PTS and have them test all of them together and fix whatever comes from that?
Any other recommendation?Leave a comment:
-
-
Re: TC-P50VT20 10 Blink Code
Perhaps number of case could give a hintAttached FilesLeave a comment:
-
Re: TC-P50VT20 10 Blink Code
maybe this manual is close enough i got the link from another forum
Leave a comment:
-
Re: TC-P50VT20 10 Blink Code
still 10 blinks. Does it indicate more like A-board, which might have defective already before mounted? Or two board at once. If only SS board would be broken then white screen should appear to the screen, isnt it? Ok, talk futher another day. Good night and much appreciation
Might be time to confirm the voltages F15v and 15V. Could mean one of the boards received is also faulty.
With just the P,D and A connected it's one of those I feelLeave a comment:
Related Topics
Collapse
-
Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?by Tynan DillI was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.
Upon bringing it home and plugging it up, it showed a standby light.
I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.
The screen seems to blackout and stay black, but with a flashlight I can see the display.
With my Playstation 4 connected via HDMI, and running a game I can hear sound.
Assuming...7 Photos -
by m1ch43lzmHi, this is my personal laptop, which the original board (lets call it Board A) blew up PU8700 (TPS51486), making a hole on the board, i had left the laptop at my desk one day with the battery fully charged and didn't touch it for a week, but when i tried to turn it on it didn't
Thought the battery was dead, so i plugged in the charger then tried to power on, the power LED blinked once, charged LED still orange, unplugged the charger, plugged in again and I noticed the "magic smoke" smell, so i unplugged the charger, removed the back cover and saw the blown IC (the "magic... -
by HakuuHi There,
This TV was auto switching off after few seconds with some vertical lines on the screen, so got a new TCON board and replaced it.
After replacing the TCON board it was working fine and i set it up with everything, used for few hours, then had the bright idea to update the software on it. During the update process, TV switched off and now no audio or video. No relay switch sound.
More Details
TV Model - LG OLED77G1PUA
Got the same exact TCON board from TVPartsToday and replaced it. But didnt transfer the EPPROM data (didnt... -
by cheeky2For anyone interested just repaired this Sony Main board TV that had a 2 blink error code, the chassis is a RB2G which is common to quite a few different Sony models. The Ceramic 10uF 25V X7R 1206 capacitor C9114 was shorted which took the smd 2A 0603 fuse out F9101. This was powering the Buck converter TPS54332 which caused no 5V output from it.
See the attached picture of the locations of both components. I also attach the best service manual I found for this board for anyone else in a similar position of trying to repair this main board. It's not specific to the TV model however it gives...01-08-2024, 05:56 AM -
by jb_BakHey guys great forum glad to have found it. I bought a Sony XBR 65X900C cheaply because it didn't work. No signs of life at all not even a light/led. All I hear is a brief high voltage sound when I throw the power to it.
Didn't see any obvious signs of damage so right away started checking voltages. This is what I see:
Power Board Connector that goes to Main board
CN6401
Pin 01 NC
Pin 02 NC
Pin 03 "BL_ON": 0V
Pin 04 "N/C"
Pin 05 "STBY 3.3V": 3.5V
Pin 06 "GND": N/C
Pin 07 "AC_OFF"... - Loading...
- No more items.
Leave a comment: