I have Lcd 40" TV. Brand OKI C40VB-FHTUV.
Main board 17MB62-2.6 and PSU 17PW82-3 (Vestel both)
I think Psu is ok because all voltages are present 3.3V, 5V, 12V and 24V but all time led is blinking (no starts).
I have been looking for information on the forum and my conclusión is corrupted FW.
I need to load firmware with pendrive through the USB port but Dont know where I can download. This is the procedure I found for OKI v32b-phtuvi (here see coment below):
1. Insert a USB flash drive to your computer, format it in FAT32 format.
2. Unzip and save ALL files that you downloaded.
3. In your pendrive should be the following files:
to. mb6X_en.bin (25MEGABYTES) * (X can be 0 or 1)
b. mboot.bin (851 kilobytes)
c. usb_autoupdate.txt (2 kilobytes)
4. ONLY TO RECORD ON PENDRIVE files with the same name as
BRING ON THE SHOCK. DO NOT rename.
5. Safely remove the flash drive from your computer.
6. Unplug the TV.
7. Insert the flash drive on your TV OFF.
8. Take control of your tv, find and press the OK button ensuring that the
CONTROL SIGNAL RECEIVER GET TO YOUR TV.
9. Holding the OK button, plug your TV.
10. The flash driver clearly quicker than when you turn
normally.
11. When the light starts flashing this rapid cadence, may stop
press the OK button.
12. Wait for the driver to stop flashing completely.
13. Replace unplug the TV.
14. Remove the flash drive from the TV. It will not be necessary. Format it again to use it
normal.
15. Connect and wait for the tv does not flash to give the button.
16. When the TV start-up, set it.
17. press M or menu key, as his command, followed by the number combination 4-7-2-5
18. There will be entering a special menu.
19. Go with the arrow to "DIAGNOSTIC" option and press OK.
20. Point to the "FACTORY RESET" option
21. Press "OK"
22. Your TV will reset completely.
23. Tune in again. will no longer launch the first installation screen in each
I thought that if I find another identical working tv. Is it possible to load the firmware on a flash drive?
thaks
Main board 17MB62-2.6 and PSU 17PW82-3 (Vestel both)
I think Psu is ok because all voltages are present 3.3V, 5V, 12V and 24V but all time led is blinking (no starts).
I have been looking for information on the forum and my conclusión is corrupted FW.
I need to load firmware with pendrive through the USB port but Dont know where I can download. This is the procedure I found for OKI v32b-phtuvi (here see coment below):
1. Insert a USB flash drive to your computer, format it in FAT32 format.
2. Unzip and save ALL files that you downloaded.
3. In your pendrive should be the following files:
to. mb6X_en.bin (25MEGABYTES) * (X can be 0 or 1)
b. mboot.bin (851 kilobytes)
c. usb_autoupdate.txt (2 kilobytes)
4. ONLY TO RECORD ON PENDRIVE files with the same name as
BRING ON THE SHOCK. DO NOT rename.
5. Safely remove the flash drive from your computer.
6. Unplug the TV.
7. Insert the flash drive on your TV OFF.
8. Take control of your tv, find and press the OK button ensuring that the
CONTROL SIGNAL RECEIVER GET TO YOUR TV.
9. Holding the OK button, plug your TV.
10. The flash driver clearly quicker than when you turn
normally.
11. When the light starts flashing this rapid cadence, may stop
press the OK button.
12. Wait for the driver to stop flashing completely.
13. Replace unplug the TV.
14. Remove the flash drive from the TV. It will not be necessary. Format it again to use it
normal.
15. Connect and wait for the tv does not flash to give the button.
16. When the TV start-up, set it.
17. press M or menu key, as his command, followed by the number combination 4-7-2-5
18. There will be entering a special menu.
19. Go with the arrow to "DIAGNOSTIC" option and press OK.
20. Point to the "FACTORY RESET" option
21. Press "OK"
22. Your TV will reset completely.
23. Tune in again. will no longer launch the first installation screen in each
I thought that if I find another identical working tv. Is it possible to load the firmware on a flash drive?
thaks
Comment