-
-
Re: Samsung LED TV troubleshooting. Help is very appreciated!
As far as i can tell BLU is connected to 13V through a resistor on the main board.Comment
-
Re: Samsung LED TV troubleshooting. Help is very appreciated!
I have tried to connect pin 12 (BLU) to 5 volts. This does turn on the backlight, but the television is still power cycling (meaning that the screen turns on and off and i can hear a relay clicking, in intervals of 2 seconds).Comment
-
Re: Samsung LED TV troubleshooting. Help is very appreciated!
It appears to be the PS pin that causes the power cycling. If i remove the PS pin from the connector the TV doesn't power cycle. But i Can still only turn the backlight on and OFF. Other functions isn't working. Any ideas?Comment
-
Re: Samsung LED TV troubleshooting. Help is very appreciated!
The PS pin is btw also called SW_PWR_OUT. So the main board is changing the State of this pin every 2 second.Comment
-
Re: Samsung LED TV troubleshooting. Help is very appreciated!
Is it at all possible to fix the main board?Comment
-
Re: Samsung LED TV troubleshooting. Help is very appreciated!
Not understanding you too well, is the Pson going high then low ?Please Do Not PM My Page Asking For Help Badcaps Is The Place For Advise, Page Linked For Business Reasons Only. Anyone Doing So Will Be Banned Instantly !
https://www.facebook.com/Telford-Tel...7894576335359/Comment
-
Re: Samsung LED TV troubleshooting. Help is very appreciated!
I still haven't solved the problem. Does anyone know a solution?Comment
-
Re: Samsung LED TV troubleshooting. Help is very appreciated!
remove t-con cable "carefully" try that and all other boards and cables connectedComment
-
Re: Samsung LED TV troubleshooting. Help is very appreciated!
desolder blue and yellow wire and solder as this pic.
may be you have pin # 17 and pin # 18 have short circuit.
Regards.Attached FilesComment
-
-
Re: Samsung LED TV troubleshooting. Help is very appreciated!
Thank you, but i have measured and the pins are not shorted.Comment
-
Re: Samsung LED TV troubleshooting. Help is very appreciated!
Hi, I know this is an old thread...did you find a solution?Comment
-
Hi everyone,
Im looking for some advice regarding my Samsung UE55MU8000 TV with main board model BN94-11606C. The TV suddenly stopped turning on and now shows no signs of life at all not even the standby light at the bottom.
Initially, I suspected an issue with the PSU, so I took it to a repair center. They tested it and confirmed that the PSU works perfectly, even on other TVs. Based on that, I started investigating the main board.
I disconnected the main board from the PSU, and the backlight turned on, which seems to confirm the main board is the issue.... -
When plugged in it will click and cycle the BL on and off, no pic and does not respond to remote. When I disconnect the cable from the PS board to the main board and then plug it in the BL will come on and stay on. There are only two boards in this set, the LVDS cables from the panel driver boards connect directly to the main board. Since the BL comes on and stays on I'm thinking the PS board is ok and the problem is on the main board. Should I order another main board or do I need to do more testing? thanks, Lee -
Hey guys great forum glad to have found it. I bought a Sony XBR 65X900C cheaply because it didn't work. No signs of life at all not even a light/led. All I hear is a brief high voltage sound when I throw the power to it.
Didn't see any obvious signs of damage so right away started checking voltages. This is what I see:
Power Board Connector that goes to Main board
CN6401
Pin 01 NC
Pin 02 NC
Pin 03 "BL_ON": 0V
Pin 04 "N/C"
Pin 05 "STBY 3.3V": 3.5V
Pin 06 "GND": N/C
Pin 07 "AC_OFF"... -
ONN 100012588
Issue: No Power, Then Rebooting After Main Board Change
Short answer: replace main board and power board
Technical answer: replace main board and Q306 & Q307 on power board.
Long answer:
TV wouldn't turn on. Power switch was fine which means the main board isn't processing the power on signal. Replaced main board. TV turns on now but randomly reboots. Bad main board? EEPROM? Tried to pull main board and got a shock touching the corner of the board. That's weird. C334 (450V 10uf) capacitor is still holding a high charge.... -
I suppose the real question is whether the existing pinouts from ether a 17IPS71 psu are cross compatible with a 17IPS12 psu? If they are then the exchange of the main boards should have no issues providing the screen is compatible with both main boards. Obviously you can change the screen configurations easily enough (providing you have the correct files) for the main board. Why may you ask would I do this? Well a lot of the smart features are no longer working on a Hitachi 48HBT62U main board I wish to give it a new lease of life!
Obviously the same LVDS connector for the screen connection...
Comment