tv will switch on and is working but,after about 15 to 45 mins the back light will go off.i have pulled the caps out [in red on pic] and checked with a cap meter,all within range,now can one of the caps go bad with heat turning the light off,leave the tv off till cool and will come back on again,have ordered new caps,is there anything that i can check that may have some bearing on the prob.the caps in red are for the inverter.
blaupunkt 32/147 led tv,no back light.
Collapse
X
-
Re: blaupunkt 32/147 led tv,no back light.
Possibly an intermittent LED inside the panel - worth checking voltages going to the panel, see if they stay where they are, or if they increase / decrease.
Failing LEDs are becoming a BIG issue with LED-backlit TVs... what was that about them being more reliable?Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: blaupunkt 32/147 led tv,no back light.
I think he is telling us the DCV at the LED connector when TV is in standby and when TV is on.Never stop learning
Basic LCD TV and Monitor troubleshooting guides.
http://www.badcaps.net/forum/showthr...956#post305956
Voltage Regulator (LDO) testing:
http://www.badcaps.net/forum/showthr...999#post300999
Inverter testing using old CFL:
http://www.badcaps.net/forum/showthr...er+testing+cfl
Tear down pictures : Hit the ">" Show Albums and stories" on the left side
http://s807.photobucket.com/user/budm/library/
TV Factory reset codes listing:
http://www.badcaps.net/forum/showthread.php?t=24809Comment
-
Re: blaupunkt 32/147 led tv,no back light.
yes it was a bad led,only one,so nothing to loose i took it off,took one off a strip i had and,it melted lol,so i bridged the gap with solder,put back together and switched on,hay presto the picture is now ok,back light is on,cant tell that one has gone.Comment
-
Re: blaupunkt 32/147 led tv,no back light.
Wow, another set with bad LEDs. Gonna become even more common...Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
Related Topics
Collapse
-
by sam_sam_samThis happened last Saturday and today I finally had time this morning before I went to work to replace two non brand capacitors
I will let you be the judge weather or not these are bad or not according to the blue ESR meter that I am using
I am comparing them to a brand new one that I installed
The display came back on and the programming was not lost which I was surprised by I would have thought that when the display went blank that so did the memory as well
I going to let it run for several days before I remount back on the wall next to the... -
by PNI E.hi guys, i need your help again...i have tcl u65x9006. while i was watching it become darker like when a movie ends, little by little the image disappear. now if i turn on i have back light on, after like 1 min i have also sound but no picuture. the back light is on i take off one at time the ldvs but nothing change always no picture. i tried to cover with a piece of paper the pin of ldvs i cover like 7 8 pins but nothing worked. the tv stay with no picture. there is a tcon board.i checked the voltage there on the fuse i have 11,8 volts. there is caps in shorts on the exit of the tcon i have...
-
by jdawg99Hi All,
I need some help with this one please. I am attempting a repair on the backlight. TV turns on and flashes the LG logo so stripped it down and found one faulty LED. Replaced it and tested on an LED tester and the strip was good. Put it back onto the PSU and it lasted about 20 seconds before going out again. Same LED had blown. Changed it for another type of SMD one (same voltage) and it seemed fine. Put the TV back together but it was quite dim. Noticed it was in power save mode so turned it off and the screen was bright. Left it on for half an hour only to come back to the... -
by cockalomgDoes anyone have a schematic for this board?
I have no output voltages, no standby voltages.
The fullbridge rectifier has a permanent 330V
there is no voltage on the two large black electrolytic capacitors​2 Photos11-05-2024, 03:01 AM -
by boyebaranhi to all
tv turn on and show logo(backlight on)than backlight turn off than red led in front blinking 7 time. the tv remote control working fine (sound on no picture).backlight changed same problem
in 65k560 how to remove protection of backlight? picture of inverter and sockets attached .
please advise me tnx4 Photos05-20-2025, 07:11 AM - Loading...
- No more items.
Comment