Re: Dead As A Doornail. Sony KDL-40EX400
Yes, POWER ON wired to STBY3.3V through the resistor. Try this trick to reveal part #: http://electronics.stackexchange.com/a/5410
-
Re: Dead As A Doornail. Sony KDL-40EX400
OK, by PSON being wired HIGH, I assume you mean the resistor in place as before.
Not trying to be anal, but as Commander Spock would say, "Infinite reminders are infinitely preferable to gross errors"
As for R6342, it IS intact and DOES show a short..
IC6301 doesn't appear to have a part number on it.. which would argue for the idea that it's proprietary..
Attached FilesLeave a comment:
-
-
Re: Dead As A Doornail. Sony KDL-40EX400
Check DC volts across C6323, C6117, C6118, C6115 -- all on the primary side with PSON being wired HIGH. Can you also check if R6342 is intact (should be a short) and get the part # of IC6301 on the bottom of the board (the large multi lead chip)
Looks like IC6301 is an "all in one" main SMPS controller and PFC controller. I hope it is not a custom Sony part or getting a replacement may be tricky.Leave a comment:
-
Re: Dead As A Doornail. Sony KDL-40EX400
Looks to be this one.Attached FilesLeave a comment:
-
-
-
Re: Dead As A Doornail. Sony KDL-40EX400
The power on pin is active high, so it needs >2.5Vdc to turn on.
Since the PFC Voltage booster did not come on with force on resistor, then you need more in-depth troubleshooting.
See PDF.
P/N of this power supply board?Last edited by budm; 02-10-2015, 12:16 PM.Leave a comment:
-
Re: Dead As A Doornail. Sony KDL-40EX400
Still dead... STBY shows 3.3v POWER ON shows 0vLeave a comment:
-
Re: Dead As A Doornail. Sony KDL-40EX400
Power to 450v Cap is 162v with resistor in place...
POWER ON to GND inline with the resistor??
IE POWER ON<===>RESISTOR<===>GNDLeave a comment:
-
Re: Dead As A Doornail. Sony KDL-40EX400
To me this indicates your power board is bad. I think main board is trying to turn on board but failing. Put the resistor back in place and check voltage across the 450V cap Also try connectingpower on to gnd again with a resistor.Leave a comment:
-
Re: Dead As A Doornail. Sony KDL-40EX400
OK, TV plugged in, POWER ON was at 3.3v...
I pulled the resistor and the meter went down to 0v...
Plugged the connector back into the Main Board. Meter read 1.9v for a sec or two, then went down to 0vLeave a comment:
-
Re: Dead As A Doornail. Sony KDL-40EX400
Hmm. That should turn it on then. Can you remove the resistor and reconnect the
PSU and main boards. Then check power on pin again - just make a note if it goes high briefly then low, or not...Leave a comment:
-
-
Re: Dead As A Doornail. Sony KDL-40EX400
Picture is not clear enough to see if you've bridged the correct pins. What is the voltage now at POWER ON, with red meter probe on POWER ON and black probe on the chasiss of the TV? (Leave the resistor in place.)Leave a comment:
-
Re: Dead As A Doornail. Sony KDL-40EX400
Thanx, Budm...
I found a 430ohm resistor and plugged it in as pictured..
No response from the TV. Still doornail dead...
Did I select the right pins??
STBY 3.3v and POWER ONAttached FilesLeave a comment:
-
-
Re: Dead As A Doornail. Sony KDL-40EX400
500 Ohms is fine, and you must remove the cable going back to the main board.Leave a comment:
-
Re: Dead As A Doornail. Sony KDL-40EX400
BadCaps was down all morning!! Started getting the DTs
OK, the closest resistor I have is a 500ohm... Too big??
And I unplug the connector from the main board side and put the resistor on the connector at the marked pins...
Good Ta Go??Attached FilesLeave a comment:
-
-
Re: Dead As A Doornail. Sony KDL-40EX400
Yea, that's my thinking. I am going to run to the shop. I'll being home some resistors and test it with Tom's idea...Leave a comment:
-
Re: Dead As A Doornail. Sony KDL-40EX400
sounds like the main board isn't turning on the power supply.Leave a comment:
-
A) TV initially dead
B) On a hunch of a locked up Google OS, plugged in a USB memory stick with latest FW and plugged it in. It booted into the update screen, completed the update and restarted to Home screen.
C) Was able to perform a Reset from Settings menu and completed out of box configuration.
D) Ran a 4K screen saver demo for about 6 hours, then turned it off for the day. Did not notice any stripes, dead zones or other artifacts in the image.
E) Powered back on and it now runs for a few minutes before relay clicks, screen goes blank, Main Board Red Digital Optical... -
Hello to everyone in this wonderful forum.
I have this SONY LCD TV KDL_46R473a
PSU GL5 APS350 :1-888-122- 12
MAINBOARD FY13_EU IP-012C101-4010
black screen ,no STB no life almost death.
on PS all the required volts are present 394V on the main cap and those on cold side 12.41V,3.45 and 3.45 are on
Also 3,5,and 12v are on.
nothing happens if i disconnect the PSU from the mainboard as on Samsung because here i think the mainboard gives the signal to the ps.
don't know what to do next all suggestions and advice are very welcome​... -
Hi,
My Sony W905 started to turn itself off an on every few minutes and blinking 8 times red in standby. A few minutes later the tv was completely dead.
I can only hear the click of the PSU when attaching/detaching the power cable. No standby LED.
Any advice? Thanks! -
Hello again lifesavers.
I have a KDL-55W755c that came in dead - not even standby light going on. Tested the power supply - all correct. Tested the output pins on the Led driver board (in which the power cord plugs in) - all seemed fine.
I got a service manual for this model and tested the DC/DC converter by checking voltages on selected components. Every voltage was present where it should be. Service manual says that in this case a "Muffin" replacement is needed. This is the moment where I got stuck as I wasn't able to Google my way through it - till this day I... -
Buenas mi nombre es carlos me uni al foro porque estoy buscando el schematic de una sony vaio pcg-41217u otras formas de escribirlo son 1p-0117j01-a012 mbx-237 numero de placa revision 1.2 o Sony VPCSB (MBX-237), en fin me gustaria y ayudaria un monton si alguien me puede dar dichi svhematic para hacer las mediciones de una laptop de la mencionada anteriormente(Sony VAIO PCG-41217U) con el fin de repararla dejo de funcionar solo prende el led de la bateria al pulsar el boton de power el disco empiesa a hacer ruido de actividad pero los leds del frontas no reflejan acividad y no enciende la pantalla....
Leave a comment: