strange fault

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • mali67
    New Member
    • Nov 2013
    • 8
    • united kingdom

    #1

    strange fault

    I have a fault on a LG 50PW450T.
    When you turn it on it flicks through the inputs like theres a stuck button.
    I have tried a new button touch control pad, still the same.
    Im thinking its a fault on the main av, but at £70 for a used one its a bit on the pricy side.
    the main av part number is EAX63902502 (1)
    Does anyone have any idead? maybe a new eprom ?
    Cheers robbie
  • Naturallyk2
    Senior Member
    • Nov 2014
    • 64
    • USA

    #2
    Re: strange fault

    Is it possibly to try a factory reset? https://www.badcaps.net/forum/showthread.php?t=24809

    Comment

    • AFajitas
      Senior Member
      • Dec 2014
      • 183
      • USA

      #3
      Re: strange fault

      What happens if you disconnect the front panel buttons and turn it on with the remote?

      Comment

      • mali67
        New Member
        • Nov 2013
        • 8
        • united kingdom

        #4
        Re: strange fault

        Originally posted by AFajitas
        What happens if you disconnect the front panel buttons and turn it on with the remote?
        It does the same,

        Comment

        • mali67
          New Member
          • Nov 2013
          • 8
          • united kingdom

          #5
          Re: strange fault

          Originally posted by Naturallyk2
          Is it possibly to try a factory reset? https://www.badcaps.net/forum/showthread.php?t=24809
          when using the remote the tv shuts down on any remote input, so cant access service menu

          Comment

          Related Topics

          Collapse

          • Rictech
            Panasonic SA-MAX770PU SMPSU board fault....
            by Rictech
            Hello everyone. 😀

            As per thread title, this unit has a serious SMPSU fault. It blows F1001, which is a 10A M205 in the phase from the mains input.
            Very first thing I tried, was simply replacing the fuse, but the replacement ceramic fuse blew immediately.

            Looking at the schematic for this PSU, I then removed what I thought was the next likely candidate: D1001 - the HV main bridge rectifier.
            This isolated the fault(no longer blows the main fuse), but does not point me to the actual fault.
            There are no devices that have exploded or otherwise show signs...
            08-26-2024, 01:05 AM
          • sam_sam_sam
            ESR meter came to the rescue again today with a PLC I/O card fault
            by sam_sam_sam
            I have been having a fun time at work with two pieces of equipment that had shorted components or shorted component cables to machine frame
            I would check what my multi meter was telling me about how many ohms I getting with the multi meter was telling versus the ESR was telling me about weather or not it really was a short to machine ground or not

            One note at first we thought that it might be a bad I/O card or a malfunction PLC including me as well but I thought I would try and see if removing the I/O cables would make a difference or not and this time it did make a difference...
            12-18-2023, 08:17 PM
          • cazi1001
            Strange fault on Lenovo ThinkPad E14 Gen. 2
            by cazi1001
            Hello,
            I have a strange fault with a Lenovo ThinkPad E14 G2 (Board No. NM-D011 Rev. 1.0).

            The first Problem, which I fixed already, was a dead TPS65944AD (USB Type-C) controller. After I fixed this fault, all functions working fine and the notebook run very well with the charger and battery.
            On the next day, I tied to start the notebook with the battery, but nothing happened. I started with the charger and on windows, I saw, that the battery was empty. And this was nearly impossible, because the battery was charged. I disconnected the battery and found out, that the board...
            03-24-2024, 04:16 AM
          • PanicMechanic
            Extech EX330 multimeter current range offset fault
            by PanicMechanic
            My multimeter has developed this fault, a few months ago. I tried to fix it, but had no success.

            The fault is that on the current ranges it never shows 0. Does not matter if the probes are open or shorted.
            As you can see from the pics, the offser is the same (just multiplied for other rages):

            -4.9 uA
            -0.49 mA
            -0.49 A

            I don't know what exactlly caused the fault.

            The meter had a battery leak before I noticed the fault, but I am not sure if the fault was present before that happened. I just did not noticed. The battery leaked...
            05-11-2021, 11:13 PM
          • spleenharvester
            Cordless Dremel 8220 rotary tool power fault
            by spleenharvester
            Hi all

            I bought this Dremel several years ago (8220 + 880 2.0Ah battery). After about a dozen light uses it developed a power fault. I asked Toolstation to start a warranty claim for me and they just refunded me in full without asking for it back instead. Would be nice to fix it instead of consigning to the dustbin.

            It is complete luck of the drawer whether it powers on or not. Sometimes it will be completely dead, no lights no response. Switching power on and off repeatedly and/or removing and reinserting the battery will eventually make it spring to life. After that...
            04-13-2025, 02:10 PM
          • Loading...
          • No more items.
          Working...