I have the smaller twin here to my personal TV. I'm trying desperately to get it going to give to my in-laws for Christmas next week. The TV had a shorted SC board which I managed to fix last night with a repair kit. Tightened loose screws all over the place when I re-installed the board. Powered it up and was very happy to see the menu pop up. However, upon viewing for a minute I realized that there was a blue haze all over the screen. Especially on dark scenes. It also started out with a spot that was much worse in the lower right corner but that improved after a few minutes. The haze however remained. I'm at work now and cannot troubleshoot but was wondering if anyone had any suggestions. Unfortunately, the repair kit took forever to get to me so if I don't order any additional parts by tomorrow I don't see having this ready to leave town with me next Tuesday. Thanks in advance for any assistance and I always appreciate the input and advice.
Panasonic TC-P46ST30 Fixed SC Board But Still Have a Display Issue
Collapse
X
-
Re: Panasonic TC-P46ST30 Fixed SC Board But Still Have a Display Issue
Oh, one more thing. In the last picture, I tried to show what appears to be temporary image retention. Any lettering or sharp edges on a picture that stays up for more than a couple seconds is leaving blue spots on the screen for 5-10 seconds. I'm sure that's related to the entire problem.
Thanks again for the help!! -
Re: Panasonic TC-P46ST30 Fixed SC Board But Still Have a Display Issue
Looks like over-diffusion. Try checking Vsus; should not be too high. Could also be Vad issue on SC board if the set-up ramp is stunted, or Ve on SS board, do you have an oscilloscope?
I swear we've seen something like this before on this forum - not sure what it ended up being.Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: Panasonic TC-P46ST30 Fixed SC Board But Still Have a Display Issue
No scope Tom. I actually just asked your advice on getting one a few days ago but it won't happen until at least after the 1st of the year. I won't be able to dig back into it until this evening (8-9 Eastern Time US). I will start by checking all the voltages. Certainly wouldn't be surprised if there's an additional issue on the SC board since it was blown and I've just repaired it.Comment
-
Re: Panasonic TC-P46ST30 Fixed SC Board But Still Have a Display Issue
TV is the same as the 50" and 55" version internally.
https://www.badcaps.net/forum/showth...ght=TC-P50ST30
Like I said, my main issue is my time restraint in taking it to the in-laws for Christmas. Certainly don't mind buying a part if I need to but it's going to have to be by tomorrow at the latest.Comment
-
Re: Panasonic TC-P46ST30 Fixed SC Board But Still Have a Display Issue
Any chance that the buffers got damaged when the SC failed? Nothing tests shorted and the guy said the picture was perfect up to the moment it died on him. I do see that some of the other repair kits come with more diodes and FETs than the one I got. However, seems the 6 I replaced along with the 4 resistors is the most common.Comment
-
Re: Panasonic TC-P46ST30 Fixed SC Board But Still Have a Display Issue
SO looks like all the resistors replaced, all 7.5ohm I guess? R422, just looks a bit different, right side in photo.
Did you check the SD SU boards ? second last photo seems to indicate it is SD board that 's having an issue. Could be the SD or SCLast edited by tw2005; 12-16-2014, 07:18 AM.Comment
-
Re: Panasonic TC-P46ST30 Fixed SC Board But Still Have a Display Issue
I believe the resistor you are referencing is just lifted up a tad on one side. The iron I have is a bit large for working on those given their size. All 4 were new and the same. I'm not showing any shorts on either buffer board but that's not to say there isn't something wrong. The problems seems worse on the lower half of the screen, but it's certainly showing up on the entire thing. I was looking for a starting point on what to check tonight. Hate the thought of buying the entire set of 3 boards but I'd do that if I thought it was going to solve the problem.Comment
-
Re: Panasonic TC-P46ST30 Fixed SC Board But Still Have a Display Issue
Also, not sure if this is a factor but I was a bit concerned with how much I had to heat the diodes and fets to remove them. I cut a hole in a piece of foil to shield the remainder of the board while I heated each one but man did I ever have to apply some heat to get them loose. I'd said a good 30-45 seconds on each one with my Weller hot air station on it's highest setting. Was concerned about heating other parts on the board.Comment
-
Re: Panasonic TC-P46ST30 Fixed SC Board But Still Have a Display Issue
Personally I doubt SU or SD would cause this issue.
Did you check the ERC IGBT driver IC? (near the inductor)Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: Panasonic TC-P46ST30 Fixed SC Board But Still Have a Display Issue
Also, not sure if this is a factor but I was a bit concerned with how much I had to heat the diodes and fets to remove them. I cut a hole in a piece of foil to shield the remainder of the board while I heated each one but man did I ever have to apply some heat to get them loose. I'd said a good 30-45 seconds on each one with my Weller hot air station on it's highest setting. Was concerned about heating other parts on the board.Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: Panasonic TC-P46ST30 Fixed SC Board But Still Have a Display Issue
Also, not sure if this is a factor but I was a bit concerned with how much I had to heat the diodes and fets to remove them. I cut a hole in a piece of foil to shield the remainder of the board while I heated each one but man did I ever have to apply some heat to get them loose. I'd said a good 30-45 seconds on each one with my Weller hot air station on it's highest setting. Was concerned about heating other parts on the board.
not real sure which way you should go if everything is hooked up right and tight. I'll have another look but it really seemed just bottom 50% affectedComment
-
Re: Panasonic TC-P46ST30 Fixed SC Board But Still Have a Display Issue
The bottom is worse but look at my 3rd picture as well as the last. It's definitely affecting the whole screen. Tom, I did not check the driver IC. What is it's location and what should I be checking on it?Comment
-
Re: Panasonic TC-P46ST30 Fixed SC Board But Still Have a Display Issue
yeah, picture 3 shows more of an issue. Test patterns / full white could be interesting. Does remind me of the SS board I accidentally removed 50% of the drive signal when I tagged a SMD 100 ohm resistor and removed it by accident.
Maybe like Tom is suggesting, something extra damaged like driver icComment
-
Re: Panasonic TC-P46ST30 Fixed SC Board But Still Have a Display Issue
And yeah, first thing I did was double check all my connections. I sure was bummed when I saw the problem. I fired it up, saw the menu, grabbed a celebratory beer to sit back and watch it for a while, and then saw all the sparkles.Comment
Related Topics
Collapse
-
by sam_sam_samI did not have any 27uf @ 50 volt capacitors but one nice thing is that it has enough room for two capacitors in parallel a 22uf and a 4.7uf @ 50 volts 22 plus 4.7 equals 26.7uf which so very close to 27uf I will show some pictures of it sometime tomorrow
This is one of the shit est boards I seen in a very long time and it was the daughter board the traces just lifting off the board I had to use the capacitor leads to repair the the traces and the main board is not any better because I had to repair several traces for the daughter board to the main board
After all of... -
Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?by Tynan DillI was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.
Upon bringing it home and plugging it up, it showed a standby light.
I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.
The screen seems to blackout and stay black, but with a flashlight I can see the display.
With my Playstation 4 connected via HDMI, and running a game I can hear sound.
Assuming...7 Photos -
by canadaboy25I have a Panasonic TC-P54VT25 that will power on and prime the display but there is no image at all.
The panel is primed as there is a slight glow from the entire panel. This means the problem should be logic related. The service manual also confirms this and recommends replacing the A or the D board.
I have tried to get the TV to display the test sequence but I have been unable to and I don't even know if this TV has a test sequence or not. I tried following tom66's instructions in post #3 on this thread https://www.badcaps.net/forum/showthread.php?t=26790. There was... -
by SoulzinkHi everyone,
I am trying to fix a samsung washinmachine power supply main board.
I already replaced it with another one to fix the machine but i want to try understand the issue with the old board.
Therefore i hope to be able to get some help to explain what to check in order to troubleshoot.
The power supply board reference is the following: DC41-00189a
I have followed one thread (https://www.badcaps.net/forum/troubl...ingmachine-rel... -
by Asraf AtbHi everyone,
Im looking for some advice regarding my Samsung UE55MU8000 TV with main board model BN94-11606C. The TV suddenly stopped turning on and now shows no signs of life at all not even the standby light at the bottom.
Initially, I suspected an issue with the PSU, so I took it to a repair center. They tested it and confirmed that the PSU works perfectly, even on other TVs. Based on that, I started investigating the main board.
I disconnected the main board from the PSU, and the backlight turned on, which seems to confirm the main board is the issue....1 Photo - Loading...
- No more items.
Comment