I have a Emerson LC320EM9B the standby light is red then I hit the power button the power light flashes 11 times then stays on green and I see the words "Digital Television" come on the screen for a second then goes out and the green power light goes out and the red standby light comes back on. I took the back off and no obvious bad caps I can see no burning or hot places I see so not sure where to check next. Ideas?? I uploaded what the boards look like.
Emerson LC320EM9B on then off
Collapse
X
-
Re: Emerson LC320EM9B on then off
i don't know if it is the same problem but this was a thread i created for a sylvania 37" but you might be having the same problem because it is pretty much the same setup except mine has 7 inverters not 5 check it out and post if that was it. if not someone here could help troubleshoot it. but it is always good of you to take pics of the back of your tv with the cover off and single pics of all the boards so we can maybe see something you may have missed.
https://www.badcaps.net/forum/showth...light=sylvaniaLast edited by philliesfan30m; 02-06-2014, 07:59 PM. -
Re: Emerson LC320EM9B on then off
in the second pic what is the label on the 2 components above the 3 resistors in a row? wow that board got hot just like someone else that posted but never said what the fix was.Comment
-
Re: Emerson LC320EM9B on then off
oh ok it looks burnt. did you check anything at all? did you check that diode between the heatsink and the transformer?Comment
-
-
Re: Emerson LC320EM9B on then off
i don't think that is the problem. for some reason it is telling it to go into protect mode i think.Comment
-
Re: Emerson LC320EM9B on then off
did you test that mosfet on the heatsink by those 2 caps i asked about earlier?Comment
-
Re: Emerson LC320EM9B on then off
it might also have a bad inverter. causing it to go into protect mode now that i think about it. take the board off and measure the resistance of the inverters. take a pic of the bottom of the board. maybe i bad inverter is causing it to go into protect mode. you should be able to tell by testing them and seeing if they are all the same then they are probably good but if 1 varies a lot then thats probably your problem.Comment
-
Re: Emerson LC320EM9B on then off
scratch the part about the mosfet for now. you might even be able to test them without taking the board off if you can get your probes on the legs. but it would be better to see the bottom of the board to see how many pins it has etc.Comment
-
Re: Emerson LC320EM9B on then off
set meter to 2000ohms and test where the arrows are pointing 1 probe on 1 pin and red on other for all 5 of the inverter transformers and also check the 2 pins above that the same way for all 5.Comment
-
Re: Emerson LC320EM9B on then off
see if you have any resistance between the primary and secondary sides of the inverters i was gonna have you do that next but you put the board back in.Comment
-
Related Topics
Collapse
-
by MOSSEPHi
Im hoping someone might be able to give me some idea of what may be wrong with my Monitor Audio RSW12 Sub.
Ive owned it since new in around 2002, so would really like to keep it running if I can, it was the first ‘decent' bit of audio equipment I ever purchased and is a little sentimental.
The issue I had was that it would power up with the red light, but sometimes the green light would not come on and I would get no bass from it. If the green light did come on though, I would get sound out of it.
I have already tried replacing all of the...-
Channel: Troubleshooting Audio Equipment
-
-
by MOSSEPHi
Im hoping someone might be able to give me some idea of what may be wrong with my Monitor Audio RSW12 Sub.
Ive owned it since new in around 2002, so would really like to keep it running if I can, it was the first ‘decent' bit of audio equipment I ever purchased and is a little sentimental.
The issue I had was that it would power up with the red light, but sometimes the green light would not come on and I would get no bass from it. If the green light did come on though, I would get sound out of it.
I have already tried replacing all of the... -
by lcdcaps1Hi
I have an 820-2610-A motherboard that has no green light.
I have noticed is when I do a SMC reset the light on the Magsafe blinks.
From My understanding, the sys onewire circuit is responsible for the green light on the magsafe
The sys onewire circuit on this model and others is more involved
I was hoping if anyone knows about this and how it works, can reply and let me know
I know this is an old model but I am sure there are people who still works on these or knows about them
I get 1.1v on the C7771 capacitor and will replace... -
by AleMontiHi everyone,
I'm trying to troubleshoot and repair this old LG OLED curved TV, model 55EG910V.
I did some basic troubleshooting and reviewed most related posts here, but I wasn't able to isolate the issue.
The TV shut itself off during playback and never came back to life - the standby light remains off. My dad claims that it has happened a few times in the past but the issue resolved itself after some time. Not this one.
After checking the basics I did the following:- I measured all voltages and as expected the only active supply is the 3.5V standby. It
-
by blazzeliaHi guys,
I have this 2011 MBP - the company I was working for, bought it at the time for a project and gave it to me after that. Later on, I gave it to my daughter which used it for normal internet browsing and office apps. At some point the, now famous, AMD GPU issue hit this laptop as well. I disabled the use of the AMD GPU following some information I found at the time (the one that, at the end, one moved AMD kext drivers to a backup location). So the laptop was using the CPU graphics and it was ok for the said daily usage. I even replaced the drive with an SSD one and it was operating... - Loading...
- No more items.
Comment