Have 11.2 volts from the 5v standby... ESR of cap is good, Resistor checks out... Not sure how the NPN works so would that cause this?
Attached Files
-
-
Re: Vestel!
It appears that the transistor has a emitter to collector short. I am on my smartphone and I don't have a pen with me to look up the zener diode voltage rating. Also check the voltage across the zener diode if its correct. If wrong value then it may be causing the transistor to be fully turned on. It has a .7v drop across the on junction. -
Re: Vestel!
11.9v at one side of diode... 0 at the otherComment
-
Re: Vestel!
Can an NPN be tested in circuit.. if so its bad...
Base to emitter = red - black _ Closed
= Black - red _ Open
Base to collector = Red - Black _ Open
= Black - Red _ Open
Emitter to collector = Red - Black = Closed
= Black - Red _ Open
I have tested this correctly haven't I?Comment
-
Re: Vestel!
If you have 11.2V into a 5V standby, I'm pretty sure the main board would have fried!!Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: Vestel!
Guess what... I didn't lol... Replaced the transistor and voila works lovely :-)Comment
-
Re: Vestel!
I am glad that it worked for you. The voltages told me shorted transistor.Comment
-
Re: Vestel!
wow, quite surprised to say the least that nothing fried! All functions work?Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Hello everyone, I'm repairing an LG TV backlight and I noticed some strange behavior when I touching the backlight strip with a missing Zener diode.
So I replaced the leds on the strips and they seemingly working fine, but soon as I touch the strip which has a missing Zener diode the whole backlight turns off for a few seconds and then turns back on.
Is this caused by the missing diode? If so what kind of zener diode should I use to replace it?.
The led strips has 9 6V leds.
-
I have bought this Zener Diode for this project what size and wattage resistor value do I need to use to get near 50 watt output
I bought this from an eBay seller but unfortunately they only had one
I bought three from Vetco Electronics these are Sylvania ECG5185A 9.1@10w A to Stud what size and watt resistor do I need to use to get near 10 watt output
I bought three of from them to also make battery packs with this output power limit in mind
I want to use this battery pack and turn it into a 9.1 output battery pack output to eliminate using 9 volt battery... -
My Element 32 inches tv (ELEFW328B) lost it's backlight (confirmed with a flashlight test) and the connector on the PCB (it has one board that has a processor chip, switch mode power supply, and backlight circuit) that has the two wires that go to the backlight LED strips has a very low voltage (28-29 volts) when turned ON, in my opinion.
Started testing components and found an SMD diode or zener that is shorted (even zero fusing resistors read a few tens of milliohms, while this thing reads zero).
I put some pictures here to show that it is labeled "M7".... -
Hey there guys. I've got a Corsair power supply that's come across my bench dead. I usually don't mess with power supplies, but it's a slow week so I'm giving it a whirl.
Taking it apart I heard a screw rattling around inside, and when I got it apart I found a couple blown components near what I think is the 5VSB area.
There's a 22ohm resistor that's melted and open, but it still has the bands.
The other part is a zener diode and it's top went to jesus, so I can't read the marking.
It looks like the diode connects the source and drain of a TNY284... -
Hello,
im actually trying to save a d1500 delay from yamaha. I found the service manual but schematic is missing and BOM list is a bit unclear as components listed have no reference linked to the pcbs... In my case, one zener diode was broken (114 code on the pcb in attached file) and couldn't be repaired : it was a zener type package. In the BOM list i found 3 reference on this board : 1S555 (can be replaced by 1N4148), RD4.7EB2 (approx 5v rectifier), RD7.5EB3 (approx 7v rectifier)...
Actually the cathode goes to VCC of sram M5M5118P, without this diode missing, i have...
Comment