Panasonic Viera Plasma TC-P60S30

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • redbank
    New Member
    • Oct 2013
    • 3
    • United States
    #1

    Panasonic Viera Plasma TC-P60S30

    Hoping someone out there can help me out. I have only had this TV for 18 months and very little hours on it. First all 3 of my HDMI ports have failed, I now have to use video cable to get a picture from my cable box . The HDMI ports have gone over the course of owning the TV but last night I had no picture and now I have a trouble code 13 blinking from the red led light on the front of the TV. Doing some searching I haven't been able to come up with a manual to try and troubleshoot my problem. I do have the manual from my purchase but it doesn't tell me anything including why there is a red blinking light . What I have found from searching is possibly my DG board could be bad (not even sure which part this is)? I have tried following some links from other posts but haven't had much success.
    Tags: None
    • redbank
      New Member
      • Oct 2013
      • 3
      • United States
      #2
      Re: Panasonic Viera Plasma TC-P60S30

      Update on the situation. The TV actually turned yesterday on and I had a picture and then I turned it off and about an hour later tried turning it back on and nothing. Very frustrated at this point.

        Comment

        • aaronwt6
          Badcaps Veteran
          • Apr 2013
          • 855
          • US
          #3
          Re: Panasonic Viera Plasma TC-P60S30

          I wouldn't know where to tell you to start on the troubleshooting on this one but I do have both the X Main, Y Main, and all the buffers on hand for this set. If you end up needing any of those, shoot me a PM.

            Comment

            • Caleb
              Smokin IC's
              • Feb 2013
              • 645
              • USA
              #4
              Re: Panasonic Viera Plasma TC-P60S30

              Not sure if it flows down to your model but on mine 13 blinks means "communication error between IC8001 and IC1100" Def A board
              Liberating magic smoke one part at a time

                Comment

                • aaronwt6
                  Badcaps Veteran
                  • Apr 2013
                  • 855
                  • US
                  #5
                  Re: Panasonic Viera Plasma TC-P60S30

                  May just need to reseat a ribbon cable if it's a communication issue.

                    Comment

                    Previous template Next

                    Related Topics

                    Collapse
                    • badcappo
                      Dead Panasonic Viera TX-P65STW50 Plasma TV
                      by badcappo
                      Hello, got a ST50 plasma TV for repair. No signs of life, not even blink codes. Opened it up to check the power supply, type MPF6914. Apparent issues from visual detection and measuring for shorts:
                      Diode type G972s6 - D101 with a short
                      Mosfet 06N90E - Q301 shorted
                      Fuse T5AH 250V - F103 blown
                      Diode D301 shorted
                      Relay DG1U-17VDC II - RL001 blown

                      I have not found a circuit diagram. Maybe someone here already dealt with a similar issue? Thanks for tips where else to check 😀...
                      11-24-2024, 11:27 AM
                    • jm1234
                      Panasonic plasma TX-P42ST50 - 6 blinks
                      by jm1234
                      Hi,
                      anyone able to provide the service manual for old plasma Panasonic TX-P42ST50E?
                      It turns off almost immediately (0~5 seconds after pressing the on/off button) and starts flashing the red diode 6 times.
                      I disconnected the left-hand side board (SC?, both the ribbon cable and the power cable to it) and also another ribbon going to bottom left board. Then the led signal is 8 flashes. According to service guide to another Panasonic plasma it would mean the left-hand side board is faulty. But I'm not sure it 100% applies to my model.
                      I checked that board for any obvious faults...
                      05-22-2024, 06:59 AM
                    • stecos
                      Panasonic Plasma main board repair (ST30 GT30 VT30 ST50 GT50 VT50),LED with 3 blincks
                      by stecos
                      Hi everyone!
                      I happened several times, in the search for help from the web, to consult this very interesting forum.
                      So I decided to sign up and I intend to participate actively by making available my knowledge and experience on the subject, I'm a new user but at the same time I'm old in the sense that I have 4 decades of experience in repairing and designing electronics but above all I'm a great passionate about the subject.

                      Having said that I come to the gist of my post on the forum as the title suggests.
                      For my passion for technology I'm now collecting several...
                      11-28-2022, 11:39 AM
                    • cloo
                      Panasonic ZT60 plasma tv with strange behavior and 8 blink code
                      by cloo
                      I recently got my hands on a 60" Panasonic P60ZT60 plasma tv (european model) that has some strange issues along with an 8 blink code.
                      It know this tv is getting old but it was once considered one of the best plasmas ever made, and i think it is still holds on to that even by todays standards.


                      So, long story short. When i first got the tv it had a very bright washed out picture with very raised blacks in all picture modes and i couldn't find the cause in the picture setting menus.
                      After doing a factory reset this problem was gone and the picture was back to...
                      01-06-2025, 06:02 AM
                    • Alicat
                      Panasonic Plasma TH-50PZ85U No screen No blinks on red power light
                      by Alicat
                      Hello,

                      Stopped by this site trying to fix my parents Panasonic Plasma TV.

                      Model number is TH-50PZ85U

                      Power comes on and the red power light stays on solid.

                      Did a few checks like hold the power button on for 60 seconds, hold the - Volume while holding the menu button, no luck, still@ blank grey screen as the screen lights up very vague.

                      I also hear a few clicks.

                      I also think my parents said there was a thunderstorm and the TV failed after that.

                      Section 6 in the service manual talks about power and no screen,...
                      10-30-2024, 10:09 AM
                    • Loading...
                    • No more items.
                    Working...