Vizio V032e stuck in standby?

Collapse
X
Collapse
+ More Options
Posts
 
  • Time
  • Show
Clear All
new posts
  • aggied
    New Member
    • Aug 2013
    • 5
    • usa

    #1

    Vizio V032e stuck in standby?

    Helping a friend with is 32" LCD that seems to be study in standby. Read a lot of posts but just can't seem to nail it down.

    I do know one of the small fuses on the main board is blown, but to be honest I think that was due to tinkering on our part. I had read a small voltage across that fuse before but later on when the alligator clips slipped and sparked it no longer read any voltage.

    I know that I have 5v at the pins labeled "5v" on the power board... but that's about all we have so far. We've got alligator clips running across that burnt fuse but still can't get the orange light to go white...

    any thoughts? I understand voltages are supposed to be read across the regulators/ Does anyone know the required voltages for this model? Will we even get readings when it is stuck in standby?
    Attached Files
  • aggied
    New Member
    • Aug 2013
    • 5
    • usa

    #2
    Re: Vizio V032e stuck in standby?

    bump

    Comment

    Related Topics

    Collapse

    • fharris1977
      Vizio D50u-D1 Dead Set No Standby
      by fharris1977
      Hi. I got a Vizio with no power or standby, and won't turn on with remote or button. I checked the voltages on the connector and all read 0.00V or nearly 0(0.050 ON/OFF pin). None of the pins are labeled STB for standby although I do see some 5V pins. Other than the obvious standby led, which isn't coming on, is there a way to check for standby voltage on this PS. I'm trying to see if my problem is the PS or mainboard. Some Vizios I have fixed with no standby led me to think it was the PS but it turned out being the mainboard. Any experience with this set would be greatly appreciated.
      12-28-2023, 10:25 AM
    • lepak06
      TV LED 4K Selecline 65S18 ( T.MS3458.U801) stuck in Standby mode
      by lepak06
      Hello

      I have an TV Led 4K Selecline 65s18 with mainboard T.MS3458.U801

      The TV is faulty with stuck in Standby RED LED. Can't power the TV.

      Before this problem , the TV stuck the picture with artefact , i unplug the AC cable and since the tv is stuck in standby .

      All voltage are OK on PSU and main board for regulator. I tried flash firmware 25Q64 with many dumps

      But the voltage on power button is 0.6V not 3.3V. When i press power button the voltage up to 0V. I tried to add 5V with Power Supply on 5V_STB and 3.3V on Power...
      01-12-2023, 01:43 AM
    • x_orange90_x
      Vizio V555-G1 stuck on wallpaper; now stuck on V logo
      by x_orange90_x
      I just got this tv today and it's getting stuck on the wallpaper. When I first power it on it goes to the V logo, then a black screen for about 15 seconds, then a Chromecast error for just a few seconds, and then finally to a wallpaper. It stays frozen on this wallpaper and does not respond to anything on the remote besides power on/off. Likewise the buttons on the tv do nothing either (besides power). I did the "reset" by holding the volume down and input buttons together for 10 seconds. It showed a message at the top of the screen saying it was Wiping Data and would restart soon. After...
      12-28-2023, 06:26 AM
    • toty79
      Hisense LTDN50K220WSEU stuck in standby
      by toty79
      Hello to all friends of the forum and well found, here I am asking for your help and sorry for my translated English.



      As per Hisense tv title LTDN50K220WSEU stuck in standby
      PSU rsag.820.5687 HLL 4855WF
      Main rsag 7.820.5842
      I enclose the psu diagram, after the first routine checks I find myself with a regular standby voltage of 3.3v blue light on steady when the power button is pressed nothing happens, psu disassembled and bench checked ... forced ignition by sending a signal 3 , 3v on the SW and PWM2 pins the psu turns on and delivers all the voltages...
      05-01-2022, 04:39 PM
    • lego1234567
      LG 32LB1R - stuck in standby mode
      by lego1234567
      Hi. I have the following problem with my TV. After connecting to mains, the standby led (red) turns on, but TV is not responding to remote control or buttons on TV. After some measurements, I found out that +5 V standby voltage is present, but I dont have ON/OFF signal coming in to turn PSU on. It stays at zero volts. After looking at the schematic of the mainboard, I should get ON/OFF signal coming in at the R1402 resistor, but it stays around +3,5 V. So I removed it and I was able to turn on TV with buttons on TV, but not with remote control.

      What could be the problem ? Thanks...
      01-21-2024, 03:39 AM
    • Loading...
    • No more items.
    Working...