palsonic tftv815hd lcd inverter transformer!

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • attainteddragon
    Badcaps Veteran
    • Apr 2013
    • 764
    • australia
    #1

    palsonic tftv815hd lcd inverter transformer!

    just wondering if anyone can point me in the direction of this inverter transformer!
    board number- dac-24to42 rev-2c
    transformer number- 2874015400

    lcd parts don't have a comparable transformer and shopjimmy and ebay don't have the boards!
    Attached Files

    if you find these attachements useful please consider making a small donation to the site

    WHY CAN'T PHILIPS USE PHILLIPS HEAD SCREWS?
    Tags: None
    • tw2005
      Badcaps Legend
      • Oct 2011
      • 6458
      • Australia
      #2
      Re: palsonic tftv815hd lcd inverter transformer!

      Try searching by LCD Panel model Number:

      CLAA320WF01U
      http://www.shopjimmy.com/dac-24t042d...t-inverter.htm

      The SJ photo is good enough to identify each component, maybe compare your board. Could be close.

      Sanyo LCD model LCD-32XR8DA may also have the same board/panel too.

      There may be a number of variants which may fit and do the same job.

      The transformer on the SJ board looks to be a different model but could be same size and pins. The PCB layout and components look much the same but check for yourself.


      http://www.ebay.com.au/itm/Inverter-...item3a6d29ee7f

      http://www.lcd-chip.com/ViewDetails10857.aspx

      If you look at this, shows same board as yours fitted to Dynex dx-lcd32-09. look at SJ and that link above also fitted to same model. Boards look the same different transformers used.
      http://www.usefulparts.com/tv-parts/...cd32-09-lcd-tv

      other models
      ELEMENT
      32LE30Q

      INSIGNIA
      NS-LCD32

      http://www.ebay.com.au/itm/DYNEX-DX-...item1c34c3779f

      http://www.ebay.com/itm/DYNEX-DX-LCD...item5654cbf224

      http://www.ebay.com/itm/DYNEX-DX-LCD...item5658e52641
      Last edited by tw2005; 08-09-2013, 10:35 PM.

        Comment

        • attainteddragon
          Badcaps Veteran
          • Apr 2013
          • 764
          • australia
          #3
          Re: palsonic tftv815hd lcd inverter transformer!

          thanks tw, you have done it again!
          lcd-chip have the transformer! woo hoo!
          now i can finally finish another one that is laying around!
          fyi, the sony one wouldn't work, almost double the resistance, but i do enjoy the researching!

          thanks again!
          WHY CAN'T PHILIPS USE PHILLIPS HEAD SCREWS?

            Comment

            Previous template Next

            Related Topics

            Collapse
            • learnmore
              Help choosing replacement transformer for Levoit 600S SMPS
              by learnmore
              Hello Community,

              I'm attempting to repair the SMPS on a Levoit 600S air purifier. The transformer is likely open. It has six pins. 2 pairs on the primary side (one pair tested open) and 1pair of legs on the secondary side. Legs on the secondary side are spread wide apart (end-to-end). I've circled them in blue. Dimentons of the transformer are 22x23mm. Marking on the transformer are EE16 1.9mH-B. Fuse for the powerboard is fuse 250V 3.15A. I've been unable to find an exact match and I'm hoping for some help here to find a suitable replacment.

              Peace
              LM...
              11-04-2025, 09:35 AM
            • eccerr0r
              inverter H tree driver imbalance in an AC inverter
              by eccerr0r
              My cheap crappy 1KW grid tie inverter (GTI) seems to keep blowing IGBTs. When I first got it, it had two failed IGBTs. It used four 60N100's (TO264). I bought 5 from a dubious source (fleabay) and replaced just the two that were dead. The GTI worked for almost two years but recently one of the two that I replaced failed. Since I had three spares, I replaced the dead one. Then a few weeks later it failed again. Weird. Well since I bought dubious China-sourced IGBTs from fleabay it could very well just be a mixture of fakes. I replaced it, but then a day later it failed again! I put in the last...
              11-16-2025, 12:34 PM
            • ohren
              Original Xbox 1.0 PSU: Foxlink FTPS-0002 Rev. B. — 12 V low, 5 V high — transformer?
              by ohren
              Hello!

              I'm looking at an original Xbox PSU: Foxlink ftps-0002 rev. B. The 12 V output is too low, and the 5 V output is too (?) high. Unfortunately I don't have an oscilloscope but only a DMM for diagnosis.

              Measured voltages with no load:

              After rectifier diodes
              12V: 6.17 V
              5V: 5.67 V

              Secondary transformer pins AC measurement (really don't know if this says anything)
              12V: 2-2.5 V
              5V: 1.04 V


              I also have another (working) Xbox psu from Delta. The same measures there, in order, being: 10.79,...
              03-18-2023, 10:33 AM
            • mikey5791
              Is it possible for transformer substitution?
              by mikey5791
              Hi all,
              Got this local made DC power supply (12/14V) given free as the transformer has melted. There is no marking or indication to identify what type or rating of transformer used.
              Fyi,. I had a busted autogate mainboard with transformer with marking 13-0-13 . Is this the 13v dc type transformer?
              My questions are
              1. How do i test to see if the transformer is in good working condition?
              2. Can this transformer (marking 13-0-13) be used to replace the melted transformer on the DC power supply?
              Hope you guys understand what i was asking. My intention is...
              11-03-2022, 02:11 AM
            • x_orange90_x
              Vizio E55-E1 bad backlights or bad inverter?
              by x_orange90_x
              I just got this tv today and it appeared to have no backlight on. After taking off the rear cover and checking again in the dark I can see that MAYBE one quadrant is lit.. But still it's quite dim. I was going to check the LEDs with my tester, and I found LED 1 and LED 2 + pins on the wire from the inverter, but I couldn't identify a ground. Nonetheless I tried using a mounting screw on the inverter board and also the chassis as ground but regardless my tester reads 300 which is what it reads when there is no voltage draw.

              I don't know how exactly to test the inverter itself. Is it...
              01-29-2025, 09:24 PM
            • Loading...
            • No more items.
            Working...