Another Philips 50PFP5532D 50" 1080i HD Plasma Television
Collapse
X
-
Re: Another Philips 50PFP5532D 50" 1080i HD Plasma Television
ok tom i have had a fiddle with the bottom board i have tried two different boards and the ribbon cable is still getting hot, but could that be because these board are broken
what's the best way to test them. i did notice a very faint spark coming from what i think are surface mounted fuses i could be wrong (the little black rectangle things), it was the top board the first connection on the rightComment
-
Re: Another Philips 50PFP5532D 50" 1080i HD Plasma Television
If the ribbon cable is getting hot you either have the heat clamps removed, or the panekl driver is defective... unfortunately the last is condemning to the panel.Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: Another Philips 50PFP5532D 50" 1080i HD Plasma Television
the heat clamp is the big long ally thing that runs along the bottom of the boards oooohhh i see now that disperses the heat evenlyComment
-
Re: Another Philips 50PFP5532D 50" 1080i HD Plasma Television
Yes, you did not remove this while the panel was active right?Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: Another Philips 50PFP5532D 50" 1080i HD Plasma Television
But even 30 seconds can cook the delicate chips embedded on them, which are not user serviceable, except by replacing the plasma panel itself... not worth it. Just put it back together and hope you get original symptoms.Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: Another Philips 50PFP5532D 50" 1080i HD Plasma Television
ok i have put it all back together turned it on half the screen is black with faint pixels showing through, you can see the faint outlines of light on the dark-side
the sticker on the screen, its a reflection of the metal back panel
if i disconnect the ribbon cables individually the part of the black bit disappears and a whites screen takes its place. i am wondering if i have shorted the bottom boardsLast edited by joehezzer; 02-08-2013, 03:59 PM.Comment
-
Re: Another Philips 50PFP5532D 50" 1080i HD Plasma Television
I think the drivers have burnt out unfortunately as before you were at least getting a dodgy picture, try reseating the connectors but I am not holding out much hope.Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: Another Philips 50PFP5532D 50" 1080i HD Plasma Television
The bottom boards don't really "short", as there's barely anything on them.
If you replaced those bottom boards perhaps swap out for the older ones that might still be good?Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
-
Re: Another Philips 50PFP5532D 50" 1080i HD Plasma Television
There are lots of resistors on them -- basically the only thing that can fail, so test them.Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: Another Philips 50PFP5532D 50" 1080i HD Plasma Television
Yes.Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: Another Philips 50PFP5532D 50" 1080i HD Plasma Television
They should be something like 0.47 ohms to 10 ohms...Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
Related Topics
Collapse
-
by celiabrownHello guys,
My Plasma Philips 37inch chassis FTL2.1 does no picture ,and goes into protection mode after 30 seconds (red led blinks at 3Hz).
Can someone has any symptom like this ?
Thanks05-09-2024, 10:56 PM -
by Cdm1212Hi,
I am attempting to repair my television. When I turn it on, it seems to start normally and then the backlight turns off after a couple seconds.
Initially on the main power board I replaced diode D1202 which was shorted, and capacitor C1201 which was bulging. I was still getting some wonky voltages, so also replaced C1204, C1250 on the main board, as well as the filter caps on the LCD module, which were 3 680uf caps in parallel, which I replaced with 2 1000uf caps in parallel.
The tv is still showing the same symptoms, although now... -
by renechhello,
I hope someone on this forum can assist me.
I have a panasonic TH-42PC77U plasma television.
the lower 1/2 of the screen has become flaky....in and out, then finally goes black and you can only see the top portion.
i have performed the reset to default settings quite a few times. Panasonic recommended..did not believe this would help...it didn't.
I have removed the back panel and looked around for something obvious...burn marks in a board, etc....nothing obvious...
I have read some posts that suggest the problem is related to the boards on the left... -
by aidanmoHello,
I've got a really strange issue with the speakers on my Philips 43PUS7506/12. It makes this awful loud buzzing now. It happened after it was attempted to be wall mounted - I think the back got squeezed and something broke.
I thought maybe the speakers got damaged, so I replaced them - no dice.- Using the internal speakers, it always happens.
- Using the headphone jack, it never happens.
- Using the digital/optical out with a soundbar - it happens after about 2h/movie runtime - it's never as drastic, it just pops in and out, but I didn't want it to damage the sound bar
-
by ArMaaN376Hello,
I am having Samsung PS51E550 Plasma TV. While the TV was working, a crackling sound heard & video went off with audio still ON. After switching it off & ON, the red LED on TV blinks six times & then off.
Opened TV cover & observed foll
a) Green LED on the small PCB blinks at @5-6sec ON & off for 3-4 secs. Red LED on logic board ON
b)Vs & Va on power supply board raises momentarily to 209v & 58v resp & then drops.
c) Cold test on Y-main board shows all 3 pins of FGPF4536 IGBT short to Grnd.
How to confirm Y -Buffer board... - Loading...
- No more items.
Comment