Panasonic TH-50PX60U, Panel or buffer board bad ?

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Sevenqi
    Badcaps Veteran
    • Jul 2011
    • 292
    #1

    Panasonic TH-50PX60U, Panel or buffer board bad ?

    Panasonic plasma tv, model TH-50PX60U, bottom left side has some vertical lines as shown in the picture. this TV has six C boards, TNPA3821 - 6, control the vertical upper and lower screen. not sure if bad panel or one of the C board bad.
    Attached Files
    Tags: None
    • Sevenqi
      Badcaps Veteran
      • Jul 2011
      • 292
      #2
      Re: Panasonic TH-50PX60U, Panel or buffer board bad ?

      Upload a picture of the back looking.
      Attached Files
      Last edited by Sevenqi; 10-19-2012, 11:10 PM.

        Comment

        • freakaftr8
          Badcaps Legend
          • Oct 2012
          • 3743
          • USA
          #3
          Re: Panasonic TH-50PX60U, Panel or buffer board bad ?

          Considering it looks like most of the panel in that corner was out I would say its a bad logic board or x drive board.
          Did I leave the soldering iron on?

            Comment

            Previous template Next

            Related Topics

            Collapse
            • howardc64
              TCL 55S425 few horizontal lines, potential failure on both side of panel/buffer board
              by howardc64
              All left and right refers to looking from rear of TV (or looking from front with TV upside down)
              • TV came with vertical bars and no image. Found faulty TVS on left buffer board. Also replaced T-Con (may have damaged the original while hot air removing components, board has slight warp) and have full image but few horizontal lines on the screen. Some of the lines appears to be 2 pixel tall while others are 1 pixel tall.
              • Disconnecting left and right buffer board potentially reveals problems on both sides with different signals (unless this T-Con require jumper like Samsung FB_TRDY1&3) Fault
              ...
              07-24-2025, 05:17 PM
            • Tynan Dill
              Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?
              by Tynan Dill
              I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

              Upon bringing it home and plugging it up, it showed a standby light.

              I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

              The screen seems to blackout and stay black, but with a flashlight I can see the display.

              With my Playstation 4 connected via HDMI, and running a game I can hear sound.

              Assuming...
              ORIGINAL POWER SUPPLY BOARD
              7 Photos
              11-22-2024, 01:46 PM
            • howardc64
              A1312 (27” iMac 2009-2011) A1407 (Thunderbolt Display) A1316 (Cinema Display) Display Black Screen Repair
              by howardc64
              Problem

              This is an LG edge LED lit LCD Display. The LEDs are on the bottom edge of the display. There are 2 bars (left and right) Each bar has many LEDs and a 6 pin connector. Each pin drive several LEDs thus is the highest current flow / heat junction. The weak lead free solder gradually fails with thermal expansion/contraction cycling and increases resistance. PSU will compensate up to a point, then when the current is too high, PSU just shut down the backlight causing a dark display. I have even seen one which the connector just fell off as solder points became completely detached....
              08-04-2024, 10:36 PM
            • m1ch43lzm
              HP Pavilion 15-eh Board DAG7HAMB8F0 - CPU throttling to 0.4GHz (PROCHOT_EXT) and black screen
              by m1ch43lzm
              Hi, this is my personal laptop, which the original board (lets call it Board A) blew up PU8700 (TPS51486), making a hole on the board, i had left the laptop at my desk one day with the battery fully charged and didn't touch it for a week, but when i tried to turn it on it didn't
              Thought the battery was dead, so i plugged in the charger then tried to power on, the power LED blinked once, charged LED still orange, unplugged the charger, plugged in again and I noticed the "magic smoke" smell, so i unplugged the charger, removed the back cover and saw the blown IC (the "magic...
              05-12-2025, 08:37 PM
            • sam_sam_sam
              Panasonic switching power supply daughter board has two 27uf @ 50 volt capacitors which I do not keep in stock
              by sam_sam_sam
              I did not have any 27uf @ 50 volt capacitors but one nice thing is that it has enough room for two capacitors in parallel a 22uf and a 4.7uf @ 50 volts 22 plus 4.7 equals 26.7uf which so very close to 27uf I will show some pictures of it sometime tomorrow

              This is one of the shit est boards I seen in a very long time and it was the daughter board the traces just lifting off the board I had to use the capacitor leads to repair the the traces and the main board is not any better because I had to repair several traces for the daughter board to the main board

              After all of...
              07-13-2024, 08:14 PM
            • Loading...
            • No more items.
            Working...