wanted to see what you guys think if it is a good deal for 50 dollars and what could be wrong with it by picture .thanks
Attached Files
-
-
Re: 47 insignia lcd tv
That is a good deal, the main board, power supply board, the inverter board, and the stand total are worth more than $50.Never stop learning
Basic LCD TV and Monitor troubleshooting guides.
http://www.badcaps.net/forum/showthr...956#post305956
Voltage Regulator (LDO) testing:
http://www.badcaps.net/forum/showthr...999#post300999
Inverter testing using old CFL:
http://www.badcaps.net/forum/showthr...er+testing+cfl
Tear down pictures : Hit the ">" Show Albums and stories" on the left side
http://s807.photobucket.com/user/budm/library/
TV Factory reset codes listing:
http://www.badcaps.net/forum/showthread.php?t=24809 -
Re: 47 insignia lcd tv
Could be as simple as a bad voltage regulator on the mainboard. Worst case, one of the chips on the mainboard is fried.Muh-soggy-kneeComment
-
Re: 47 insignia lcd tv
thanks for feedback will buy it.will post pictures soon as i get it .Comment
-
Re: 47 insignia lcd tv
Well bought the tv unfornately I think I might have a bad panel one of the tcon ribbon gets hot and starts to burn ribbon strip.I tried another ribbon did the same thing it is the left side the rights seems to be fine.will post pic in few phone won't allow itComment
-
Re: 47 insignia lcd tv
what panel is in it? Had a westinghouse 47" that had the "glowing black screen" and the panel was the fault.Comment
-
Hello, I'm new to the group and to trying to repair a LCD TV. During the past few years, I've been collecting/repairing/restoring vintage personal computers (Commodore, Apple II, Atari, TRS-80, Texas Instruments, and Timex Sinclair). This has been my retirement hobby. Now I've gotten interested in trying to repair a LCD TV that I have and used regularly when working on vintage computers.
The LCD I'm working on is a Insignia NS-LCD019. I've downloaded the service manual that I could find, but it must be a different revision since not too many items in the service manual match the TV... -
Just wanted to get some feedback,
whats peoples' success rate with cof bonding repairs..... -
Having a new problem with the 19" Insignia that I modified with one of my automatic turn on circuits. That is now completely disconnected so that is not the issue. I was doing some modifications on that circuitry and managed to short something out on the underside of the power board.
Actually found and bought the service manual (who knew it was even available?!) which brought me to the High Voltage Startup Circuit controller chip.
Looking up that chip number- LD7575APS brought me to the attached datasheet. I have marked my voltage readings on the schematic sheet (open in new... -
I have a weird backlight issue on the above Insignia Plasma that I am coming up empty on researching.
The display is darker on the left than on the right side of the screen. It uses 4 U shaped plasma tubes. I have had it apart deep enough to tell you that the tubes are bright as they should be at the electrode ends but dim as they get to and go around the bend.
Since it is all 4 tubes it seems like it would be an inverter/backlight board but obviously can't be a blown up component as it does still somewhat work. I'm thinking low voltage but no idea where to go beyond...06-10-2023, 01:36 AM -
Hi,
I just replaced the battery on a Google Pixel 5.
After that the proximity sensor isn't functioning properly any more. It is constantly activated. So when playing a voice message on Whatsapp, the Screen instantly turns off.
Checking with a sensor app I can verify weird behavior of the sensor. It is triggered when nothing is near and sometimes works correctly when squeezing the phone next to the sensor hole.
The rubber seal is on again (as mentioned in various suggestions in other forums).
This smells like a cold or broken solder joint. So I'd like to reflow...
Comment