Re: tc-p50gt30
Well after replacing transistors 3 times and them shorting out every time I powered the tv on.I checked resistors 8 ohms and also had replaced ic driver and transistor.I checked all caps,diodes and resistors they all tested good.
Saw tvtimmy on fake ones,tried another batch I have bought few months earlier they looked like better quality.Used them and the Sc board turn tv no more poping noise.Weird thing is a bought them from same supplier probably bad batch or fake.
Thanks for all your help.Tv is now working.
Announcement
Collapse
No announcement yet.
User Profile
Collapse
-
Re: tc-p50gt30
I replaced the ones you mentioned and the diodes but soon as it turns on I hear a poping noise they short out.
Leave a comment:
-
-
tc-p50gt30
My is sc board is shorting out replaced the 30f131 and rf1501 .Soon as i turn the tv on it shorts out.So what i did was put a light bulb in power cord when i turn tv on it lights on for a sec or two and tv shouts off.I disconnect the sc board from power supply and bulb lights up.Also disconnect the ss board and bulb still lights up.When i disconnect Ps2 on power supply the bulb does not light up and gets a 8blink code.I was wondering if my power supply is shorted.Looks like that supplies power to sc board....
-
Re: Tc-p55ut50 8 blinks
They said they have it
[url]https://encompass.com/item/9529293/Panasonic/C0ZBZ0001936/[/url]Re: Tc-p55ut50 8 blinks<br /> <br /...0001936/[/url]
Leave a comment:
-
Panasonic tv will not connect to internet
All my Panasonic tv's will not connect to wifi the see the router.the just won't connect.They were working fine just suddenly stop working.I can use Ethernet cable and it will work just not through wifi.Any ideas what I can check.
-
-
Kdl-40ex600 is panel shorted out
Working on kdl-40ex600 have standby 3.3 no led.I jumpered standby 3.3 to power on with 1k resistor with wire that goes back to main board disconnected.There was no other voltages present measured main cap at 60v .Then I noticed on top tv burning smell and a little smoke coming out.this mean the panel is shorted out.
-
Re: New Power Supply and Main board Still No Power
Working on kdl-40ex600 have standby 3.3 no led.I jumpered standby 3.3 to power on with 1k resistor with wire that goes back to main board disconnected.There was no other voltages present measured main cap at 60v .Then I noticed on top tv burning smell and a little smoke coming out.this mean the panel is shorted out.
Leave a comment:
-
Re: Icloud locked iPhone 6 plus
Looks like only true way is in hardware unlocking
Leave a comment:
-
Re: Icloud locked iPhone 6 plus
Too bad it will not work iPhone I did try to get it unlocked but told me it was locked unlocking service but was told it was reported lost.but when I checked imei said it was not reported lost.That was not covered under 100 percent guarantee to unlock it or money back.I told them that is not what there website said so they refunded me my money.
Leave a comment:
-
Re: Icloud locked iPhone 6 plus
i saw a video where a guy removes a resistor or a cap dont recall which one it was.from a ipad and downloads wifi software and was able to restore the ipad and remove icloud.i wonder if it would work on iphone.
Leave a comment:
-
Re: Icloud locked iPhone 6 plus
I would like to learn this also where I can get ic chips I need.
Leave a comment:
-
Re: Icloud locked iPhone 6 plus
When you update the phone would it icloud lock again.if all you did was delete the setup file or is it permanent fix.
Leave a comment:
-
Icloud locked iPhone 6 plus
I was wondering his the a way to unlock iPhone that has Icloud lock.Was looking at phon lab teachable they claim the can teach u how to unlock any iphone.Brother bought phone that has Icloud lock told him it was basically a paper weight unless he just wants it for parts.my question is has any dealt with phon lab teachables website. Or can point in right direction to learn how to unlock iphone.thanks
-
Re: Tc-p55ut50 8 blinks
Sorry i did not answer earlier i got it from sears.Just saw your email, tw2005 was the one who gave me the link.After replacing ic it worked great still using tv as of today.Should have posted the results and link.The ic on 55 was smaller size ic Than one on 50.Weird thing is shopjimmy includes ic on 50 but not on 55 inch.You will also have to replace mosfet again.
Leave a comment:
-
Dvr8-4000
I am not sure if this right place to put this thread but since it is video.I thought it might be,I am looking for schematic or service manual.What happened is a had a bad power surge and it took out my dvr8-4000.I am trying to find schematic so I can try to repair it.Any help would be appreciated thanks.
-
What bga machine to buy?
I am looking for reccomendations on which bga machine to buy for working on main boards ,laptop mother boards,and xbox chips and maybe ps3 chips.Any information of past experience on machines you have used is apprecatied.thanks
No activity results to display
Show More
Leave a comment: