Re: LG 42LC46 problem
I repaired this same TV (it's now my main TV.) It could be T-con, but double check your soldering on the capacitors is good. As the TV warms up, maybe the joints are cracking. Does the TV give a good picture for 10 minutes at a time? Try using a hair dryer to localise the fault if it is heat related. Also double check the LVDS connector is seated properly.
-
LG 42LC46 problem
Hi guys n gals..im a newbie here so a big hello n happy new year.
I bought this model lcd tv from a friend ..it was completely dead..after opening it up there was 4 10v 2200uf caps bulged..so i replaced them with rubycon same values.It powered up fine and worked ok for 10mins then the picture would go but sound remains..the backlights would also stay on.
If i take the t-con board out then turn on i get the same result no picture only sound..could replacing the t-con board fix my issue..any help in my matter would be greatfully received..thx
-
Hello all ~
Hope this finds you well. This LG 82UN8570AUD (April 2021 model) 4K UHD television has full audio capabilities but video is compromised / problematic.
When I picked up this large LG tv it had a full black screen upon startup. Previous owner said it just went black one day. No popping sound or anything else of note.
I got the display to work by taping off several traces of the right-hand side ribbon cable on the TCON that leads from TCON to PANEL. However, despite dozens and dozens of attempts to find the right combination / range of traces taped... -
I have an LG Plasma TV 60PM6700 for the past ~12 years.
In the last ~3-4 months I have been having some issues.- Problem: It started with random picture disappearing (sound still worked).
Frequency: Happened about once a week.
Solution: Had to turn off TV wait a few seconds before turning it on again. - Problem: Then it got worse and the TV started to shut down and when turning on the no picture just sound.
Frequency: Happened about once a week.
Solution: Had to turn off TV wait about 10-20 seconds and turn it on again to solve. - Problem: TV shuts down
- Problem: It started with random picture disappearing (sound still worked).
-
Hi I need help with a Samsung un43nu7100 BN94-13191C/BN41-02635A with boot loop problem even with tcon jumper.
I've already try tape method and same happen, if I disconnect both flex from mainboard to panel tv boots normal even I hear Samsung sound.
When I solder jumper to make t-con work with or without panel or panel cables connected it still reboot or power cycling.
What I noticed is that there's no voltage in VHG, HAVDD, PANEL_3.3V, AVDD_17V or 12v near dc-dc chip.
I check capacitors and diodes and didn't find any short IN MAINBOARD.
Measured all power supply... -
Just bought this for 10 bucks yesterday hoping to fix it. The guy said water dropped inside from a dehumidifier hose and it started showing black and white vertical bars then went blank. When I got it home and turned it on it came on fine and displayed correctly but I was noticing faint vertical bars in the image. After a little bit I turned it off and back on and it was a black screen again. I opened it up to check for water damage and corrosion but didn't find anything of the sort. I cleaned the ribbons anyway and reconnected them but still got a blank screen. If I disconnect the right side... -
This thread is about trying to get an Universal Main Board to work with a Sharp TCON and panel.
I have a Sharp LC-46D85UN TV that has had a main board issue. Since this model is from 2009, I am not able to find an exact replacement of the main board. Instead, I decided to see if I can future proof this tv by getting a Universal Main Board (T53U21.2) from China to work with the Sharp TCON (CPWBX4291TPZA) and panel. The universal main board supports a 8 bit dual channel LVDS interface whereas the TCON requires a 10 bit dual channel LVDS input. I have modded the LVDS connector to match...
Leave a comment: