pioneer pdp505pg plasma help

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • confusedall
    Member
    • Jun 2011
    • 19

    #21
    Re: pioneer pdp505pg plasma help

    so, with all the checks and indications its definitly a power supply problem

    Comment

    • confusedall
      Member
      • Jun 2011
      • 19

      #22
      Re: pioneer pdp505pg plasma help

      I have found a tech who is willing to help me solve this issue,, also i have (on its way ) a pdp 435 which has the same power supply. I have noticed on second hand sites in NZ ,alot of pioneers are bombing out. Fingers crossed as this solving this could help out alot of plasma lovers.
      will keep updating as I know the frustration of reading forums only to get to a dead end because the final results are not added,.

      Comment

      • confusedall
        Member
        • Jun 2011
        • 19

        #23
        Re: pioneer pdp505pg plasma help

        well its going with a second hand power supply, will keep on with the old one and try to figure out what made it die

        Comment

        Related Topics

        Collapse

        • Tynan Dill
          Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?
          by Tynan Dill
          I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

          Upon bringing it home and plugging it up, it showed a standby light.

          I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

          The screen seems to blackout and stay black, but with a flashlight I can see the display.

          With my Playstation 4 connected via HDMI, and running a game I can hear sound.

          Assuming...
          11-22-2024, 01:46 PM
        • sam_sam_sam
          Desoldering gun station modified to use a 18 volt @ 20 amp switching power supply
          by sam_sam_sam
          I have wanting to do this project for quite sometime now and I finally found a switching power supply that will work on this desoldering gun station ZD-915 that the original switching power supply took a shit and just was not worth trying to fix it because this switching power is not quite big enough to handle the heater element and the vacuum pump

          One note when I tested the switching power supply and the voltage control board I noticed that this desoldering gun heat up much faster than the original switching power supply which I was really surprised by to the point that I might buy...
          03-31-2024, 02:12 PM
        • lp20th
          Samsung Plasma TV Power Supply Issue
          by lp20th
          I have a vintage 2008 Samsung 50” Plasma TV, Model code PN50A550S1FXZA with a power supply part number BN44-00222A. I repaired the power supply board several years ago finding a couple of cold solder joints on the back side of the board and it's worked great up until now. Recently a fried sound occurred with the smell of burnt electronics and the TV shut down. Trying to turn it back on yielded the typical relay clicking with no TV boot up. Upon investigation, removing feeds to the other boards within the TV it was found that disconnecting the logic board from the power supply allowed the...
          11-28-2023, 10:28 AM
        • fab13
          Power supply PS4 FAT - ADP- 240R cuts 12 Volt in 1 sec -Why?
          by fab13
          I have a PS4 FAT edition chu-1000a with the power supply (ADP-240R) that is acting up.

          After checking that it comes from my power supply and by activating the 4.7Volts with clamps, the 4.7

          The power supply starts, but cuts instatantly with a small snap on the primary side and after measuring the voltage which climbs to 10 Volts at the start and drops.

          - No short circuit around the DPN012A chip (Probably the voltage regulator for the 12 V output)

          It looks like an overload and the power supply goes to safety

          - No primary...
          04-05-2023, 04:15 PM
        • pixelcap
          Pioneer Plasma 111FD To Solder or Not to Solder.
          by pixelcap
          Hello out there in Badcap land.

          I have a Pioneer plasma that gave me the dreaded 8 red blink and shutdown, I have been trying to trace the failure points. On my last inspection while replacing a Y Sustain Board I noticed on the original and replacement board some missing solder, the points of connection
          are from the Digital Address Board and the Buffer Boards. I have included the pictures, should I resolder these points or are they unsoldered intentionally? Any help would be much appreciated.

          Thank you

          Pixelcap...
          03-08-2025, 07:10 PM
        • Loading...
        • No more items.
        Working...