No inputs on my Philips flat HDTV 50PF9631D 50" plasma

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • DarknQuiet
    New Member
    • Nov 2010
    • 1
    #1

    No inputs on my Philips flat HDTV 50PF9631D 50" plasma

    Last year our plasma had died and Sears came out to repair it. We needed a new power supply. I took the power supply to work and repaired the 2 caps on the board. The tv now powers up great, the only problem is that none of the inputs work at all. They did before the caps were replaced. Could I have plugged in a cord on the wrong place? There was one small connector on the left side of the board that could have plugged into 2 differnt places. Or could a different board gone bad in the process? Thank you for your time and any insight that you could share.

    DQ
    Tags: None
    • PlainBill
      Badcaps Legend
      • Feb 2009
      • 7034
      • USA
      #2
      Re: No inputs on my Philips flat HDTV 50PF9631D 50" plasma

      Originally posted by DarknQuiet
      Last year our plasma had died and Sears came out to repair it. We needed a new power supply. I took the power supply to work and repaired the 2 caps on the board. The tv now powers up great, the only problem is that none of the inputs work at all. They did before the caps were replaced. Could I have plugged in a cord on the wrong place? There was one small connector on the left side of the board that could have plugged into 2 differnt places. Or could a different board gone bad in the process? Thank you for your time and any insight that you could share.

      DQ
      Here is the link for the service manual. Since you couldn't be bothered to include a picture of the back of the set, you can look the proper cabling up yourself.

      PlainBill
      For a number of reasons, both health and personal, I will no longer be active on this board. Any PMs asking for assistance will be ignored.

      Never be afraid to try something new. Remember, amateurs built the ark. Professionals built the Titanic.

        Comment

        Previous template Next

        Related Topics

        Collapse
        • bohaboha
          PHILIPS 32pfl3403d Flat-panel TV Upgrade Assistant problem
          by bohaboha
          Hi trying to update my Philips cause in retail mode not possible to get out from it i get this message in update site : Error message: no data exception. Your reference: Request ID (server_1930105)
          how to fix it thanks
          02-05-2025, 09:23 PM
        • valvashon
          32" Philips PAL TV from India- should I get it or leave it for somebody else?
          by valvashon
          I know this isn't troubleshooting related but thought it was the best place to ask. There is a supposedly working 32" Philips flat screen originally from India for free near me on FB Marketplace. It's a PAL receiver but will do NTSC (?) from the HDMI inputs. Will add the model number later. I like quirky stuff but have plenty of TV's/monitors around so I don't really know what to do with it. Should I get it and see if there is a compatible NTSC/ATSC tuner board that could be swapped in?

          Val
          09-12-2025, 11:09 AM
        • alro7779
          Philips 32PFL4901/F8 BA4GF0F0102 2 Not getting standby led
          by alro7779
          Hello, guys!

          The same 32" Philips TV I was having video issues, but now I don't have standby led at all. Someone here shared with me the schematic of the power supply, and checking the voltages, I see right after the resistor R604 I'm getting 1.6 v which is too low for enabling the Gate of the Q601 mosfet (the diagram says 4.2). On the R614 resistor I'm getting 181 V in and 117 V out, then through R603 I'm getting the same 117 V in and 59.9 V out, finally getting the latter voltage in the R604 BUT getting just 1.6 V out, which is the voltage that goes on to the Gate of the Q601...
          09-14-2025, 12:25 AM
        • G33RT
          Philips 8200 series 65PUS8204/12 stuck at Philips Logo
          by G33RT
          Philips 8200 series 65PUS8204/12 stuck at Philips Logo, it does not reboot it just stays on the logo.

          It does power up when pressing the power button.

          I already try the power button while plugin the plug with no result.
          Also put the latest firmware autorun-TPM191E_R.001.004.100.000.upg on a MBR/FAT32 USB stick at USB port2 with no result either.

          Could this be an PSU or eMMC issue ?
          07-19-2025, 03:43 AM
        • dclass-pro
          HP 440 G2 no power after short in flat lcd
          by dclass-pro
          Hi all guys, I need your help. On a HP 440 G2 - LA-B181P laptop I was changing the speakers and the pc worked fine everything ok.
          After closing it all with all the screws I realized that it would no longer turn on. I opened it and found that the flat cable of the LCD was shorted. I ordered a new flat but the motherboard still won't turn on, as soon as I connect the power supply the connector LED always flashes and the power button stays on.
          I tried to check the voltages and the 3v and 5v are there, on the battery pin (with no battery connected) I have about 2v.
          I tried to...
          08-11-2023, 07:47 AM
        • Loading...
        • No more items.
        Working...