Are these switchers suitable for SMPS?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Pentium4
    CapXon Be Gone
    • Sep 2011
    • 3741
    • USA

    #1

    Are these switchers suitable for SMPS?


    In the datasheet: http://te-epc-lpc.web.cern.ch/te-epc...0MOSFET_ST.pdf it says "High voltage NPN power transistor for standard definition CRT display" May be a stupid question, but is this what it was specifically designed for? Or would these be a good option for upgrading 13009's? Thanks
    Attached Files
  • tom66
    EVs Rule
    • Apr 2011
    • 32560
    • UK

    #2
    Re: Are these switchers suitable for SMPS?

    They are designed for 15kHz flyback application with high off-state breakdown but relatively slow speed and low cost. Might work, but not intended for that application.
    Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
    For service manual, schematic, boardview (board view), datasheet, cad - use our search.

    Comment

    • senz_90
      Badcaps Veteran
      • Aug 2013
      • 328
      • Indonesia

      #3
      Re: Are these switchers suitable for SMPS?

      try it with ammeter in series with mains voltage. i am curious too! ! if this work maybe i would upgrade my cheap ass psu which has 13007. but aware when the amps goes high slowly and this looks like not applicable.
      "There is no shortcut to be successful. No pain, no gain."

      Best Regards
      Rudi
      Thank You

      Comment

      • momaka
        master hoarder
        • May 2008
        • 12170
        • Bulgaria

        #4
        Re: Are these switchers suitable for SMPS?

        I *think* they will work.
        Data sheet shows a test where the transistors are running at 64 KHz and 1.6 uH inductive load. I'm not sure what the inductance of a PSU main transformer is, though, nor if running them at this high of a frequency would mean that you have to de-rate their specs. But try it and see. Just make sure to use the light bulb trick so parts don't go
        If you want to try it with a more significant load but still don't want to plug it straight into the wall, use a portable heater, a toaster, coffee maker, toaster oven, or something similar rated in the range of around 400-600W or so. This should limit the current if something does go *poof* so at least your fuse won't blow.
        Last edited by momaka; 02-07-2014, 07:30 PM.

        Comment

        Related Topics

        Collapse

        • dkneyle
          Onkyo DX-V500 Laser Disc Player - weird SMPS fault
          by dkneyle
          This relic from a technology path that came to a dead end (but still has historical interest) was brought in with a dead SMPS, which is based around a MK1210 device. I got it going after a battle. It seems to have a strange design - if it's not getting feedback that the secondary is OK it cause the big FET to go into full conduction and overloads resulting in a blown fuse at best or something worse! I'm using a Dim Bulb Tester (70W/230V) which thankfully has saved the day a number of times whilst repairing.

          Now, it loads a CD OK. The motor voltage output (which is built onto the SMPS...
          02-01-2022, 02:08 AM
        • shamsudeen
          Hi, Can we use SMPS Bench Power Supply for Laptop troubleshooting?
          by shamsudeen
          Hi all, I just need to know that, can i use SMPS type power supply to test and short circuit detection on a laptop motherboard?
          I saw 95% of repair guys are using only Linear bench power supply. linear bench power supply is pricy, thats why i planned to get one SMPS supply.

          i know that in linear power supply the noise will be very low comparing to SMPS supply....
          07-19-2025, 07:14 AM
        • abhishekkumar1902
          Huntkey HK340-72FP SMPS shut on load above 2 amps
          by abhishekkumar1902
          I have this Huntkey HK340-72FP PC SMPS where I am facing a strange problem where the SMPS shuts down when the load on any of its 12v output rails goes above 2 amps while the rating of each 12v rail is above 10amps capable.

          I have checked the following:
          1. All output caps are OK, and all output rails read correct voltages at no load
          2. All output diodes are OK
          3. NTC is ok
          4. Hi voltage cap on input correctly reads 150uF on LCR meter per the spec, also the bridge rectifier is OK
          5. No short in main switching MOSFET
          6. All other components...
          12-18-2022, 09:52 AM
        • madan1
          Mackie Th15 SMPS low Vout
          by madan1
          Hello,
          I'm troubleshooting a PA speaker Mackie Th15 (schematics attached).
          It is basically a smps with amp and some dsp.
          The issue is that on the secondary side I read +/- ~23V instead of the expected +/- 38V. Indeed all secondary side and feedback/aux rails are like 1/2-3/5 of the expected values.
          Q2, Q3, C35, C40, C33, C36, C41 and C42 were tested out of circuit with a component tester and read fine. Most of the other components on the primary were tested in circuit and seem to be fine. +HV to -HV on primary is ~330V.
          By the way, the ferrite core of L10 is broken,...
          02-16-2025, 04:15 PM
        • rewease
          Replacement for the Siemens Bakelite caps in an early 1980s SMPS
          by rewease
          Hi everyone,

          There actually was a time when early SMPS and late bakelite housed electrolytic caps coexisted in high end industrial gear. A friend of mine just got himself a CNC milling machine form that time with its first set of now 41 year old caps still installed in the PSU... and it's malfunctioning.

          Two of the caps have already leaked slightly onto the board. I have not desoldered or measured any so far but they should qualify for replacement.

          Now I'm wondering what to put in there as a replacement. First idea was state of the art low-ESR Nippon KY,...
          09-17-2023, 12:53 AM
        • Loading...
        • No more items.
        Working...