Apple Multiple Scan 15AV Display.Help identifying a resistor

Collapse
X
Collapse
 
  • Page of 3
  • Time
  • Show
Clear All
new posts
Previous 1 2 3 template Next
  • tony359
    Badcaps Veteran
    • Oct 2018
    • 259
    • United Kingdom
    #41
    Re: Apple Multiple Scan 15AV Display.Help identifying a resistor

    No worries! Without a new tube it’s kind of pointless to invest too much time on this anyways. And worst thing that could be is that the thermistor needs replacing.

    I might have access to other tubes, if and when I source another one I’ll check that one as well thanks for your input as usual!

      Comment

      • tony359
        Badcaps Veteran
        • Oct 2018
        • 259
        • United Kingdom
        #42
        Re: Apple Multiple Scan 15AV Display.Help identifying a resistor

        I made a repair video for this monitor - Badcaps is mentioned of course (even though I said badcaps.com...)

        Thanks for all your help, I hope you find it entertaining!

        https://youtu.be/3u7vCqdEBw8

          Comment

          Previous 1 2 3 template Next

          Related Topics

          Collapse
          • ugamazing
            Assistance with identifying resistor value on 820-02918 A2992 board?
            by ugamazing
            Working on a 2023 M3 A2992 unit with 820-02918 board, and it uses a new USB-C power architecture, with rectangular controllers. I do not have a perfect-matching board, so have been repairing this one the old-fashioned way (slowly).

            I managed to blow-away a single resistor that I can't find and can't determine the value of. It connects to ground, so I went ahead and stuffed it with a 100K resistor in case it's a simple pull-up. But, I'm now having issues with that side of the board, and am curious if it's possibly related to this resistor! I have no schematics and no board view, so...
            09-06-2024, 08:33 AM
          • a_p3rson
            Apple Watch Charging Controller Schematics / Boardview - 820-02601
            by a_p3rson
            Hi there,

            I'm looking for anyone who might have information on Apple's embedded Apple Watch charging daughterboard, ID 820-02601. This is currently used by Anker in their Apple Watch charging products, but likely by other Apple partner brands as well.

            You can see the board referenced in ChargerLab's teardown of the Anker Y1811 3-in-1 MagSafe cube - they discuss the "Apple Watch wireless charging circuit" about 2/3rds down the page. It's not pictured, but the board ID reads 820-02601-A, which sure sounds like Apple.
            This daughterboard uses an interesting...
            04-21-2025, 11:41 PM
          • dutchgaucho
            Need help identifying resistor on Asus FA507RC DA0NJNMBAD0 schematic
            by dutchgaucho
            Hi colleagues,

            Looking for a schematic DA0NJNMBAD0 or the MP2845A 6-phase PWM controller.

            Working here on a DA0NJNMBAD0 rev D motherboard (Asus FA507RC) with liquid damage. Board has some tiny corrosion around the MP2845A controller and one resistor is missing. I need to know the value of the resistor, but no schematics are available. Not even for the MP chip or anything similar (this is a 6 phase PWM controller).

            On one side of the pad 20V is present. The other side connects to a cap and to pin 16 of the MP2845A. Resistor seems too small for VCC...
            11-09-2023, 11:27 AM
          • mrkmpn
            Help identifying resistor?
            by mrkmpn
            This resistor is on a small board the fan connects to in a Brother MFC L5900DW. The fan does not work, and when testing this resistor it shows no reading all the way from 4M ohms, down the a continuity test, so appears to have failed open.

            I've tried using a coupld of resistor calculators online, but I'm not sure which end is which on the resistor, and going both directions on the calculators I run into a value that doesn't have the correct color as an option.



            I, believe the colors are black gold violet black orange, but maybe I'm mistaken on one of th...
            01-19-2023, 11:09 AM
          • jinu_j
            Dell 2209WA - power supply - Fusible Resistor replacement
            by jinu_j
            Hi

            I am trying to repair an ancient Dell 2209WA Monitor which suddenly shut off with a pop sound. On investigation found that one of the fusible resistors had blown. Further investigation identified multiple components as faulty because of which the fusible resistor blew. Please refer the attached circuit diagram showing the components that were found to be damaged.

            1. FR950 - blown fusible resistor - 0.2 Ohm 1W
            2. Q950 - shorted Q950 MOSFET - 650V 10A N Channel Mosfet
            3. R835 - Blown Resistor - 20KOhm SMD resistor
            4. D930 - Shorted Schottkey Diode...
            05-03-2025, 10:51 PM
          • Loading...
          • No more items.
          Working...