mec 16xx dump with info block

[pokyss1]

Vous devez fournir votre fichier MEC et votre numéro de série. Il existe quatre versions pour ce modèle.

Numéro de série Carte système : L1HF9C300MT
Numéro de série de l'unité système : pf216zhf

[pokyss1]

SYSTEM BORD SERIAL NUMBER:L1HFC9300MT
SYSTEM-UNIT SERIAL BORD NUMBER:PF216ZHF

[pokyss1]

good ficher

[hoaca388]

SYSTEM BORD SERIAL NUMBER:L1HFC9300MT
SYSTEM-UNIT SERIAL BORD NUMBER:PF216ZHF

What is your problem ? Both files are full 00, reading failed.

[pokyss1]

What is your problem ? Both files are full 00, reading failed.

i cant read this file i always ihave errors to read vertyanovo and ht809 houw can do .
thax

[pokyss1]

good file naw for unlock

[hoaca388]

good file naw for unlock

Try

[pokyss1]

Try

i try this bat the laptop not turne on

[hoaca388]

i try this bat the laptop not turne on

Does the laptop work with the original file ?

[pokyss1]

Does the laptop work with the original file ?

SORRY I HAVE errer
sorry i have errer withe file this fil withe machin working good

[hoaca388]

SORRY I HAVE errer
sorry i have errer withe file this fil withe machin working good

This is what you read, from top to bottom.

[nesredin]

I followed Maxpower3's instructions and it worked. Follow him, you will also succeed.
Let's thank Maxpower3.

hello how to read and write with rt809f mec1663 with this x1 carbon
NM-B861 REV 1.0

[pokyss1]

hello how to read and write with rt809f mec1663 with this x1 carbon
NM-B861 REV 1.0

yes

[khaledmosa99]

hello i got thinkpad t14 gen1 20s0 with burn mec1663 i replaced it with a new one i got the jtag connection with my vertyanove programmer try to cut ec when i write it i got blinking white led 3 times only can some one help me to fined the file flash+epperom
nm-c931 rev 1.0 my s/n PF2A58EN
thank all for help

[saman mawlod]

[QUOTE=hoaca388;n3615433]


lenovo p52
type 20ma-s6hh00
sn pf-1ns7hl
mec1653
can unlock

[jaglion19]

This is what you read, from top to bottom.

I have a Dell e7440 la-9591p motherboard, no matter what I did on the device, I couldn't start it. It uses MEC5075. On the first page, someone shared the jtag paths for tx390, I searched from the schematic and found the same legs. Can I make this read by soldering it in the same way as SWOD? or with rt809f? or what are its legs? Also, I think the place where it says rp1 is for jtag, but there is a resistor with 103 written on it. Can I remove it, solder the 5 paths and 3 gnds and read it?

[djacksod]

I am posting the mec1663 Lenovo T14 nm-c931 1st gen intel 10th that I read, the eeprom address where the password is located is at offset 0x300.

[Maxpower3]

I am posting the mec1663 Lenovo T14 nm-c931 1st gen intel 10th that I read, the eeprom address where the password is located is at offset 0x300.

lines 350 and 360 should not be deleted

It's easier to find your way around with the decrypted file

[antongoikoetxea]

Thanks to everyone for the help.
My case was a ThinkPad X1 Carbon Gen 7 with motherboard NM-C661. I used an SVOD3 and the pinout from the picture I’m attaching. The reset is not needed when using the pull-down resistor.

In the SVOD software I selected EEPROM, and once the dump was read I changed the data from 0x300–0x34F to FF. After reprogramming, the password issue was solved.

Many thanks again to all, and I hope this can help anyone else who has the same model.

[osman68i]

Hi Badcaps Team,

T15 Gen1 with bios lock.

SN: PF2RVTMS

I have checked the dump but I cant find the location of the pass