HP Probook 450 G9 password

[xander007]

use my post # 107 its the same. all instructions are there your's is U85
https://www.badcaps.net/forum/troubl...89#post3694589

I took BIOS u72 as a basis, added part of update 1.04 to remove the image (screen saver when turning on). Then I figured out how to read the DMI zone and, using the HP BCU utility, wrote all my information and exited the BIOS editing mode.
Thank you very much for the tip.

[Samy33]

Hello everyone,

I have an HP ProBook 450 G9.
I need to remove the administrator code from the BIOS to reset the PC.
I extracted the BIOS chip dump, but I don't know if this is the correct chip to take the dump from.
Serial number 5CD3091R26
Thank you in advance.

[Samy33]

Hello everyone,

I have an HP ProBook 450 G9.
I need to remove the administrator code from the BIOS to reset the PC.
I extracted the BIOS chip dump, but I don't know if this is the correct chip to take the dump from.
Serial number 5CD3091R26
Thank you in advance.

Hello again
I forgot the motherboard number DA0X8SMB8H1 REV: H. I have a doubt about the dump!!!
For the dump, I copied it from the top chip, not the EC.
Thank you.

[xander007]

Hello again
I forgot the motherboard number DA0X8SMB8H1 REV: H. I have a doubt about the dump!!!
For the dump, I copied it from the top chip, not the EC.
Thank you.

You will need to write down both microchips (main+ec) and write down your details (serial number, laptop model, etc.) manually.

[SMDFlea]

Hello everyone,

I have an HP ProBook 450 G9.
I need to remove the administrator code from the BIOS to reset the PC.
I extracted the BIOS chip dump, but I don't know if this is the correct chip to take the dump from.
Serial number 5CD3091R26
Thank you in advance.

The file you posted is too small it`s only 256KB ,you have chosen the wrong chip yourself or the programmer auto-detect selected the wrong one.

[Samy33]

The file you posted is too small it`s only 256KB ,you have chosen the wrong chip yourself or the programmer auto-detect selected the wrong one.

Hello I have a GQ4X programmer, but the chip reference isn't in it. I tried the closest one, but apparently without success. I ordered a CH341a programmer today. Once I receive it, I'll read the chip and reapply it, as well as the EC. Thank you for your reply.

[Samy33]

The file you posted is too small it`s only 256KB ,you have chosen the wrong chip yourself or the programmer auto-detect selected the wrong one.

Hello I'll reread the bullet points and repost the two dumps, thank you. I suspected there was a problem, thank you.

[Samy33]

Hello Xander 007 and Chip SMD

Please remove bios and EC password.

What should I do once rewritten?

Here are the original dumps
HP ProBook 450 G9
Motherboard number: DA0X8SMB8H1 REV: H
Serial : 5CD3091R26
Thanks to you

[Samy33]

Hello

I think the EC dump reading isn't correct. I'll repost when I'm sure I've read the EC chip correctly. Sorry, my clamp isn't working properly. Thank you.

[Samy33]

Hello Xander 007 and Chip SMD

Please delete the BIOS and EC password.

What should I do once it's overwritten?

Here are the original dump files I managed to read by unsoldering the chips:
HP ProBook 450 G9
Motherboard Number: DA0X8SMB8H1, Revision: H
Serial Number: 5CD3091R26
Thank you.

[Samy33]

Good evening

Did I forget something on my password request?
Thank you, sincerely.

[Samy33]

any help please

[SMDFlea]

any help please

Your BID is U72 , try https://www.badcaps.net/forum/troubl...89#post3694589

[Samy33]

Good evening,

do you want me to take the dumps from this link and write them to my chips?
But aren't they from my computer?

[dimah77]

Hi Guys,
Please need to unlock this HP 450 G9
S/N : 5CD3045ZY2

[LBTT1121]

Hi Guys,
Please need to unlock this HP 450 G9
S/N : 5CD3045ZY2

try and feedback

[dimah77]

try and feedback

both files are the same, no change made