Hi I'm currently trying to fix this board, the problem is that when I press the power button it turns on for a couple of seconds then turns of and the current is only 0.02A, it never consumes more than that even if it's on or off. What I found is that the VCC_CORE is missing and +1.35V_VDDQP also. But the 3.3V and 5V are present. I already replaced the following: PUM1, PQM1, PQM2, UK1, PUZ1, PUZ2, PU101. I didn't notice any liquid damage or any broken parts, I replaced those with the hope of it coming back to life. I also checked if there is a short on those missing voltages and they're not shorted.
-
-
Re: HP 15-R212NL LA-B972P Rev1.0
Why change so many components randomly?? +1.35V is missing , so why mess up with vcore section. Without +1.35V rail core and gfx will never rise. So just concentrate on +1.35V rail and check the ram ic's requirement. Have u flashed known good bios with clean me?? Check resistance on all big grey coils.
-
Board had no history of liquid; unsure of drop history, but no signs of damage of any kind worth noting.
Charger sitting at 5v/0a. PPBUS is at 1.9v-0.9v steady cycle (peaks, drains, loops). Confirmed CHGR_EN_MVR is missing, but DCIN was reaching ISL just fine, so replaced ISL--no change at all. Confirmed pp3v8_aon is also missing--and being unsure *exactly* which signal appears first (or if they are simultaneous), I inspected PMU/U8100 area and found no shorts, but also found PP3V8_AON_MPMU_ISNS_VIN missing (not shorted). Replaced U8100 just in case (have had them fail in weird ways),... -
Hi everyone,
I recently acquired this card from a seller who was selling a PowerMac G5 for parts. He mentioned that the video card was probably broken too.
Upon closer inspection, I can tell the reason why it won't work: it's missing a bunch of CAPS! (it's also missing an inductor - 1.0uH).
It's a nice card as it's one of the few AGP cards that will support 2560 x 1600 resolution on a PowerMac G5 using a 30" Cinema Display.
Looking at the card, it appears to be missing the following:
1x 1.0uH inductor - orange square
2x... -
Hey guys.
Need help with this one.
Fan not spinning due to missing PWN Fan signal.
Also 5 seconds from powering up it freezes, unless in BIOS.
But as soon as Windows starts to load, it will freeze.
CPU is COLD / Room temp when it freezes.
I've replaced the CPU, same problem.
Replaced SIO/KBC IT8987e and reprogrammed - same problem.
Replaced fan - same problem.
Replaced flex cable from board to daughterboard (which has fan connector on it) - same problem.
Checked the Thermal sensors around CPU and Board to the SIO/KBC and...08-19-2024, 05:22 PM -
Hello. I would need some advice please.
My son's MBP suddenly stopped working and is now only getting the green-then-orange light on Magsafe and no fan spin.
He brought the MBP into the house (22 deg C) from a very cold conservatory (-3 deg C) and turned it on straight away. The Mac suddenly died a few minutes later.
I examined the logic board and couldn't find any signs of water damage, corrosion, blown up components etc. Nothing was ever spilt on it, and the logic board looks immaculate.
I have already replaced the logic board with another... -
Hello,
I have re-soldered the loose pins on the RAM slot which is a common fault on these models..
It charges and turns on the power LED but is missing several voltages like RAM and CPU do not come up which I believe is due to MAINON & SUSON being missing to turn these supplies on..
What I am un-sure of is what is the ITC chip waiting for to send out these signals, what are the requirements?
I have checked these lines in diode mode and they seam normal -> 600.
I have checked to see if they come on for even a fraction of a second...
Comment