Wistron JE70-CP MB - turns off after 32 sec.

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • GlobalPlayer
    New Member
    • Nov 2019
    • 3
    • Germany
    #1

    Wistron JE70-CP MB - turns off after 32 sec.

    Hi together,
    I am new at this forum and just for learning an understanding i took this old mainboard from a 17" Packard Bell Laptop.
    Battery is dead and I run it with a power adapter only.
    It turns on, I get image on the the screen, fans start running and I can enter bios or bootmenü (I removed the hdd). After exactly 32 seconds it turns off and I can start over again.
    I checked it with a stop watch, every time exactly 32 seconds, doesn't look like a faulty cap or something like this to me.
    More than a system check fails at the same stage but when I can enter bios or bootmenu the system check should already be completed, right ?
    i removed both RAM-Modules, tried with only one or the other, i applied new heat sink and replaced the 3V Button Cell, same result.
    In the schematics I found sheet 43 (Run Power) and measured some voltages but I have no idea what can cause the system shut down.
    Some hints for me ?
    Thanks a lot in advance

    GP
    Attached Files
    Tags: None
    • ktmmotocross
      Boardkiller
      • Feb 2014
      • 3581
      • slovakia
      #2
      Re: Wistron JE70-CP MB - turns off after 32 sec.

      clean bios me

        Comment

        • mcplslg123
          Badcaps Legend
          • Jun 2015
          • 7262
          • india
          #3
          Re: Wistron JE70-CP MB - turns off after 32 sec.

          Check U55 ic.

            Comment

            • GlobalPlayer
              New Member
              • Nov 2019
              • 3
              • Germany
              #4
              Re: Wistron JE70-CP MB - turns off after 32 sec.

              Thank you mcplslg123, that was Bullseye !
              U55 was the culprit (or one of the external temp.sensors).
              I couldn't find out which one but most likely GPU-Sensor.
              So i lifted up the DXP3 leg of U55 and and tried what happens.
              You know what ...it stays on.
              Fan turns on and off, everything looks ok.
              Thanks again and a happy new year !!

                Comment

                • mcplslg123
                  Badcaps Legend
                  • Jun 2015
                  • 7262
                  • india
                  #5
                  Re: Wistron JE70-CP MB - turns off after 32 sec.

                  Glad you fixed it. happy new year to you mate.

                    Comment

                    Previous template Next

                    Related Topics

                    Collapse
                    • Stephen
                      MacBook Pro 14" M1 Pro Turns on functions then turns off when I plug in USB C cable
                      by Stephen
                      MacBook Pro 14" M1 Pro Turns on functions then turns off when I plug in USB C cable to reset the computer. I disconnect the battery fully and then reconnect it and it won't turn back on. After letting it sit for a day I plug the battery back up, and the MagSafe 3 cable and it powers on and stays ons, once I plug in a USB C cable into the port closes to the MagSafe port it turns off and the Amber light turns off and won't turn on. No water damage, nothing, I want to do a DFU restore to wipe the computer since the customer stated they did an update and ever since it just decided to not work...
                      03-15-2024, 09:37 AM
                    • www
                      LG L192WS-BN backlight turns off after 1 second
                      by www
                      I am testing an old LG L192WS-BN monitor I have that gives an image, but has a backlight issue. When you turn it on the backlight turns on 1 second and it turns off, turns on again, 1 second and it turns off and stays off. Using a flashlight I can see there's still an image.

                      I replaced a bulged cap on the main board, but made no difference. I also got another exact same model monitor that has a broken ccfl (the connector got ripped from the panel and the main screen connector is also broken so I can't use this panel to test), tried using the main board from this one, same issue....
                      03-24-2024, 05:26 PM
                    • BMCappelletti
                      Lenovo Thinkpad E14 Gen3 stuck on "To interrupt normal startup, press Enter" screen
                      by BMCappelletti
                      Hi everyone.
                      Lenovo Thinkpad E14 Gen 3, stuck on the "To interrupt normal startup, press Enter" screen.
                      Found a lot of people with this issue, but with no definitive answer. Some people managed to get away accessing BIOS, going to Startup and turning off "Option Key Display". For me that only removed the interrupt normal start up message, leaving only the Lenovo logo.
                      Most people say hitting Enter does not work. It's true, if you wait a few seconds. But if you hit Enter right away you get the options to enter BIOS (which works), run diagnostics (goes to a...
                      02-18-2025, 12:22 PM
                    • andrhouseolly
                      Dell Precision 5510, AAM00 LA-C361P Rev:2.0 turns on, no image.
                      by andrhouseolly
                      Hi.
                      I kindly ask you to help me solve the problem.
                      Dell Precision 5510, motherboard AAM00 LA-C361P Rev:2.0
                      The board turns on, there is no image.
                      Read more. When the power supply is connected, the front panel indicators light up briefly.
                      When you press the power button, the button indicator lights up. The board works
                      there is no image, there is no matrix initialization, there is no image on HDMI.
                      When turned on, the fans do not spin, but when they warm up they start spinning.
                      When you turn off the button, the fans spin up to full speed for a short...
                      05-11-2024, 03:14 PM
                    • Egidio85
                      Samsung UE55F8000SZ Turns on and off immediately
                      by Egidio85
                      good morning, I have a samsung UE55F8000SZ tv that turns on, shows the logo and turns off after 1-2 seconds.
                      This defect happens continuously, hearing the classic click of the relay every time.

                      Power supply board BN44-00636B

                      disconnecting the mains and lamps from the power board always causes the same problem.
                      Is it normal that without anything connected this power supply turns on and off cyclically?
                      any suggestions on what to check?

                      thanks in advance
                      ​
                      03-11-2025, 12:45 PM
                    • Loading...
                    • No more items.
                    Working...