Which sensor used for compass in an iPhone?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • caphair
    Badcaps Legend
    • Nov 2011
    • 1249

    #1

    Which sensor used for compass in an iPhone?

    I have an iPhone 7 Plus where screen rotation and gps works but the compass does not rotate. It will however show cordinates.

    Anyone know if the compass app uses the same sensor as screen rotation?
  • diif
    Badcaps Legend
    • Feb 2014
    • 6978
    • England

    #2
    Re: Which sensor used for compass in an iPhone?

    All the ICs listed here https://www.techinsights.com/blog/ap...one-7-teardown

    At the bottom of that page. Alps Compass HSCDTD00xA I would think it is that.

    Comment

    • Jesse James
      Senior Member
      • Sep 2018
      • 95
      • Canada

      #3
      Re: Which sensor used for compass in an iPhone?

      Great info thanks

      Comment

      Related Topics

      Collapse

      • CapLeaker
        AcuRite 5 in 1 temperature sensor replacement repair
        by CapLeaker
        Got a new victim:

        AcuRite 5 in 1 Iris outdoor weather station not updating the temperature / humidity anymore. The original sensor is a SHT21. Also there are identical other sensor manufacturers. I chose the HTU21D to replace the original SHT21. Both have identical specs. I've had two failure modes with these sensors.
        A: outside temp stuck at -40? It's cold here at times in Canada, but not that cold!
        B: stuck at some temperature and maybe updating once in 12 hrs or so.

        Easy solution is to go to AcuRite website and purchase the sensor. Right?...
        04-15-2025, 01:32 PM
      • groomit
        Google Pixel 5 - Proximity Sensor Issues - Reflow/Replacement procedure tipps wanted
        by groomit
        Hi,
        I just replaced the battery on a Google Pixel 5.
        After that the proximity sensor isn't functioning properly any more. It is constantly activated. So when playing a voice message on Whatsapp, the Screen instantly turns off.
        Checking with a sensor app I can verify weird behavior of the sensor. It is triggered when nothing is near and sometimes works correctly when squeezing the phone next to the sensor hole.
        The rubber seal is on again (as mentioned in various suggestions in other forums).

        This smells like a cold or broken solder joint. So I'd like to reflow...
        06-11-2025, 02:21 AM
      • Gcnewbie
        Dell Latitude 5570 Ambient thermal sensor reading -127 Degrees C
        by Gcnewbie
        Forgive me this is my first request for help on this forum, so if i've screwed up or not followed the rules i should have i apologise profusely.

        I have a Dell Latitude 5570 that was randomly shutting down, on further investigation i found that the machine had been shutting down due to thermal events as noted by windows event viewer.
        My investigations lead me to the dell diagnostics screen, where i found that there were two sensors out of range which had been causing the shutdowns, one of which was the GPU thermal sensor and the other the ambient sensor.
        I opened the...
        03-29-2024, 06:55 AM
      • otoluk
        Auriol weather station humidity sensor
        by otoluk
        I have two Lidl LD6273 Auriol units with DCF77 radio for time update.
        I really like the idea but the cheap moisture sensor(guess HR202L) inaccuracies make the device unreliable. Also not clear why indoor and outdoor unit sensors being same type doesn't match. For example I place both units on same table and indoor unit shows 23% humidity while outdoor sensor shows 39%. What I found out is that I get better readings if cleaning the solder points of sensor inside with isopropyl alcohol.
        Looking for replacement sensor which I could solder in place of HR202L resistive sensor but need...
        11-06-2024, 07:57 AM
      • corrize
        Soldering plastic low profile FPC close camera CMOS sensor ?
        by corrize
        Hello, I will have to solder a very small FPC connector (pins : 0.3mm), on the pcb of CMOS sensor, it is very close. I was surprised by movie on ytb, someone soldering directly with hot air directly on the sensor without kapton, nothing.
        CMOS sensor seems resist to high temps.
        But I also directly saw sensor broken because a blocked motor at the corner became very hot and probably bent the metal frame and cracked the sensor.



        I have low melting point solder.
        I will probably test hot air directly on one of plastic connector (I have a lot) at 320 degree on a test
        ...
        07-12-2024, 02:21 PM
      • Loading...
      • No more items.
      Working...