Re: hp 14-am096tu system fan error 90b
@SMDFLEA the two caps near fan connector is connected to ic with a marked S32B 5388
@SMDFLEA the two caps near fan connector is connected to ic with a marked S32B 5388
-
-
Re: hp 14-am096tu system fan error 90b
@ON/OFF the board id is
INERINL-6050A2822501-MB-A01
Comment
-
Re: hp 14-am096tu system fan error 90b
@KMMOTOCROSS the 5 leg chip has marke 58ICComment
-
Re: hp 14-am096tu system fan error 90b
anyone please help on thisComment
-
Re: hp 14-am096tu system fan error 90b
anyone can help on this please still I havent solved this issueComment
-
Re: hp 14-am096tu system fan error 90b
the voltages on each pin1=0v pin2=0v goes to ground on continuity pin3=0v
pin4=3.3v pinv=0v. on diode mode pin1= 0.500 pin2=0 pin3=0.700 pin4=0.600 pin5=0.500Comment
-
Re: hp 14-am096tu system fan error 90b
Assume pin 2 is the GND of this IC the rest of the pin's seams to be fine
If Pin 4 is the enable Signal to Drive Swatch on +5V to Fan & HHD you are missing +5V input
What if you put a jumper +5V to fan & HHD and see if the problem goes off
Replace those 2 caps if you can
What pin of the 5 Leg ic did you inject 5V ?Comment
-
Re: hp 14-am096tu system fan error 90b
if i injeck 5v on pin 5 on the ic the fan turns on because this pin is connector to the capacitor near the hdd connector and two caps near the fan connectorComment
-
Re: hp 14-am096tu system fan error 90b
I think this series have 2 variant model, one fanless and next with fan.
Link HD image:
https://drive.google.com/open?id=0Bw...0hQTHdYaE1VQUU
Credit to RimasComment
-
Hi all!
HISENSE 65E7KQ PRO
RSAG7.820.13512 - chassis
MT9618BAATAB - cpu
RSAG7.820.12059 - power
HD650Y3U77 - panel
KLM8G1GETF - emmc
The TV does not turn on, the standby indicator is on. All voltages are present.
Emms is dead. Not readable, not detected.
Replaced emmc.
But with another dump there is no launch
Terminal log
UART
<
AC_ON
RPMB key is not yet programmed
HASH1_VERSION=0x00000000 64bit
E-B
FDE enabled
layout pattern onebin by SAR7,0... -
one of our new (only 4 year old) 1KVA APC UPS stop working and through error P13 contact customer support.
the equipment is out of warranty , upon investigation, we found the inverter board has the fault on the output hybrid relay circuit.
The inverter output relay is parallel by SCR/Triac to enhance the relay performance or other means.
We replaced the SCR with new device,, but the device is not power on as expected.
Further research on the issue found that, the error P13 (event ID 107) is latched on the UPS nvram/MCU and need to clear/reset using a service procedure....09-26-2025, 09:00 AM -
Hello Sharp TV experts
Our Sharp LC-80LE642U displays one short one long flash error code which is a backlight error. I went into service mode and there were 8 lamp error counts recorded. I reset the count to 0 and did a reset. The last monitor error cause was 16 B00014639:12. 16 is the code for backlight error. I tried to power the tv up but went back into error mode.
> I checked voltages on the power supply board and they all check out .. including 3.28 volts at the error pin.
> There is power to the cpu and T-CONN and no faults found there. The cpu has a flashing...01-24-2025, 11:51 PM -
Hi everyone.
I have a HP Elitebook 850 G8.
Serial: 5CG2324XM0
ProdID 6L8D5EC#ABA
It has a Winbond W25Q256JVEN Chip.
I need to remove BIOS Password.
I made a dump with an CHA341A programmer and NeoProgrammer 2.2.0.10.
Attached my dump.
I also used the HP Unlocker tool to create an unlocked file (I followed the guidelines)
I also downloaded latest HP BIOS Update (SP158137) which includes 3 .bin files. I found the Number T76 in my original dump, so I used: T76_01210000.bin
What I did:... -
Hi,
I have a 2014 vintage Philips 60PFL8708S/12 that suddenly died in the middle of the kids watching a show.
The relevant service manual for the chassis is available here.
The TV no longer powers on, and leaving it powered on for a few minutes results in the layer-1 error with 2 blinks.
When I short the SDM to ground I get the layer-2 error code 53.
The inside of the TV has no damaged components and no swollen capacitors.
In SDM-mode when all the power rails are left on despite entering the protection mode, I tracked down and measured...
Comment