Hi friends , I have received from a customer this pavilion dv5 with this mb DAUT3MB28C0, the problem is short in power and missing component near battery connector I think a capacitor and a diode, it's possible to say wath is pc120 and c654 ? thanks
DAUT3MB28C0 missing components on battery power circuits
Collapse
X
-
Tags: None
-
Re: DAUT3MB28C0 missing components on battery power circuits
You need the schematic.What revision number is the board .
DAUT3MB28C0 Rev: -
Comment
-
Re: DAUT3MB28C0 missing components on battery power circuits
Rev C is the ATI graphics version. Does it have DDR2 or DDR3 . There isn`t a free schematic for the ddr3 version , http://**************/load/noutbuki/.../307-1-0-29432 .For the DDR2 version schematic there isn`t an ATI version,only Nvidia, so there will be differences but you can use it for reference .Comment
-
Re: DAUT3MB28C0 missing components on battery power circuits
It's important to note that the one component is actually marked PC128 and not PC120. It's a 10uF 25V capacitor.
I'm not sure if the schematic available for purchase is any different or if they are all pre-production versions that don't show C654. There are also boardviews available, and they may or may not show C654. Any revision that shows it should be fine, as that circuit is pretty much the same for all of them.
There's a thread on a Polish site where the exact same caps burned up. They ended up using a 2200pF 50V capacitor for C654 simply because that's what PC182 is. But that was just a wild guess. C654 certainly is a lower capacitance part than PC128 though, and is for reducing higher frequency noise on that power rail for either stability or EMI compliance reasons.Comment
-
Re: DAUT3MB28C0 missing components on battery power circuits
dear friend, if your mobo has ati or nvidea-then its a colossal waste of time as all these mb has problems in graphics chip. So consider this also while investing your time on it.Comment
-
Comment
Related Topics
Collapse
-
by BowlineMy question pertains to understanding the control circuity inside a Dell PT434 type battery used in Dell E6400, E6410 and other Dell notebooks?
Does anyone have a circuit diagram for the inside of a Dell PT434 battery and/or a description of how the control lines work to control this battery?
My reason for asking is I have a battery which I cannot get to charge beyond 1% in a Dell E6410 or E6400.
The LED bar graph charge indicator on the battery shows one LED lighted when the info button is pressed.
I have tried multiple different Dell power adapters. My Dell... -
I bought a Vostro 3400 motherboard (LA-K033P) to upgrade over my damaged Inspiron 5593 (LA-J091P) board. Everything else is ok except for the battery. This battery I am using now is already a replacement one since I disposed of the bloated original one. Back in the Inspiron 5593 motherboard, the battery charges fine and is identified just fine. However, with the upgraded motherboard, suddenly the replacement battery is labeled as "Not a dell battery". When I borrow a similar battery from my colleague (which did not have replacements yet), it is identified and charges just fine.
... -
The ISL88739 & ISL88739AHRZ are a highly versatile combo battery charger
configurable for operating as either a Hybrid Power Boost (HPB)
charger or a Narrow VDC (NVDC) charger, supporting 2-, 3-, or
4-cell batteries. Both configurations allow the battery to work with
the adapter together to supply the system load when it exceeds
the adapter capability, referred to as system Turbo mode. HPB
charger configuration reverse-boosts battery energy to the system
bus to help the adapter provide the system power in Turbo mode.
NVDC charger configuration...-
Channel: Common Parts Library - Datasheets
11-05-2024, 03:28 PM -
-
by ferah831208Hello guys, i need help with this problem, I have a NM-D041 mobo, it came with low impedance in 3v linear regulator rail, the cause was a damaged EC controller ITE8227e-192. I ordered a new one and replaced it. This laptop have a different chip for keyboard management and it8227e pins for programming ITE chips are not accesible through keyboard interface, I flashed it using i2c interface pins with vertyanov programmer because laptop was dead and SPI flash didn't have power (only 3v EC) so it couldn't access firmware stored in SPI memory. I read SPI and extracted it8227 firmware from original BIOS...
-
by huzoHi, so the old battery was getting error stated it's capacity is starting too get low and should be replaced, so the customer bought a new one and replaced it, but the new battery was also getting this notice that it's capacity is getting low and should be replaced, so i took the laptop for testing and the battery is charging at the terminal at 8.03V , the voltage of the battery is 7.7V, and drawing around 600mA when charger is put and the laptop is off...so that should be ok... but the bios system test doesn't recognize the battery and can't do the battery test and so is the hp battery manager,...
- Loading...
- No more items.
Comment