looking for a good programmer that can flash *Laptop* ; *Tv* ; *Car* ; *Bios*
-
-
Re: Good programmer
A single programmer can not be found to do them all properly. You need at least 2 powerful programmers. If you buy cheap programmers, you need 3 programmers. All the programmers which you buy, should be able to do programming for the following interfaces:
- SPI
- Jtag
- KBC
- TV Bios interface (that I do not know what it is.)
- ECU Bios interface (that I do not know what it is.)
A very good programmer is TNM5000 which is expensive. I do not know whether it is available in your country or not.
You can use a combination of EZP2010 and SVOD which are good and powerful.Last edited by caspian; 02-12-2018, 03:13 PM. -
Re: Good programmer
I don't like SVOD, becoz it needs extra $10 each to activate ITE and novuton.Comment
-
Re: Good programmer
i do my work with CH341A and hand made Willem 3.1 (i also have ver 5.0e for some new chips) and some hand made adaprers
https://www.ebay.com/itm/CH341A-STC-...sAAOSwgN5ZpSEe
https://www.ebay.com/itm/PCB5-0E-Wil...oAAOSwupladCDQ
cannto do sio chips with thoseIm Back... sort of...
Comment
-
Re: Good programmer
Thank you brother.
1- I have the SVOD but I can not master its full use (I can not flash the KBC - ITE - ENE and other) I still have some trouble using.
2- I also have the TL866CS which works well for the moment but only flash bios. not the KBC ITE ENE NUVOTON and othersComment
-
Hi guys
I have a TL866 CS Eprom programmer and up until now it did everything I needed to do
However for the first time I have come across a 1.8V Eprom and my programmer will not do 1.8V
I need to program a 25Q64FWTG
I could splash the cash and buy a V11.71 TL866II. These come with various attachments and the kit including a 1.8V adapter is either €62 with 12 adapters or €68 with 1 7adapters. I also have the option to buy just the programmer for €46.70, if I could get the 1.8V adapter separately and use the other eprom adapters from... -
Common SPI bios chip programming Questions and Answers
----------------------------------------------------------
Q: I have a bios request,i can`t post my backup as i can`t read from the chip.
A: If you can`t read from it how do you expect to write to it ?.
Q: Why is my bios chip unreadable ?.
A: The programmer is faulty or has a worn or broken zif socket.
The USB cable is frayed,connector pins worn or some other physical damage.
Not enough amperage or voltage to power the programmer properly.
Bad...09-02-2021, 04:40 PM -
This is a shot in the dark, but I was just using my RT809H programmer and it got stuck in a certain state so I power cycled it. Now, the device LED just flashes quickly and does not connect to the software. I've tried to update the BIOS of it and it fails. I went so far as to remove the ROM from the programmer itself but it's some weird chip (I believe ATMEL, but I can't find any datasheet on it) so I've been unable to read the BIN from it w/ my other programmer. Chip has ATMLHC4C56BM CN written on it (I think). I'll upload an image. I have the programmer's BIN ready to program it manually. Anyone... -
PS4 1215A HDMI DIODE READINGS GOOD EVERYTHING GOOD BUT NO PIC? everything is good! what else can it be? if hdmi diode values are good that means encoder and filters are good right? idk what else it can be guys...01-05-2023, 12:32 AM -
I have a 60 inch Samsung UN60EH6000F flatscreen TV. The screen went black a few months ago Sound is good, backlight is good, no menu. I replaced the TCon board with a used board purchased from Ebay. It worked fine for a 3-4 months, then the screen started ‘fading' back. Once again, sound is good, backlight is good, no menu. However, this time the picture looks fine for about 10-15 minutes, then fades back. If I power cycle the TV, the display reappears, for another 10-15 minutes, then fades black again. Repeatable ever time.
I ordered a supposedly ‘new' Tcon board this time, and...
Comment