tps51225c issue

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • rookieme
    Badcaps Veteran
    • Oct 2014
    • 396
    • Greece

    #1

    tps51225c issue

    Hi,
    I have a LA-9981p with liquid damage.
    The 5 and 3 V were missing and VIN pin at tps51225c was burned so I replaced the tps and connected the VIN line.
    Now the regulator is burning hot and I get no voltage at PL100 & PL101.
    So far I have removed kbc, all 4 upper & lower mosfets of tps51225c, open pads PJP100 - 103 and replaced again with a new regulator.
    The tps still burns hot, I get no short at VREG3 or VREG5 and I get the 3,2 and 5V stable at their pins.
    Anyone have an idea what to try?
    Attached Files
  • caspian
    Badcaps Legend
    • Oct 2015
    • 1589
    • Laptop

    #2
    Re: tps51225c issue

    how much voltage is on Vin now?
    have you checked tps51225's pins for being shorted together or to ground?

    Comment

    • rookieme
      Badcaps Veteran
      • Oct 2014
      • 396
      • Greece

      #3
      Re: tps51225c issue

      vin = 17,4V
      So far I've checked all pins and there is non shorted to ground.
      From optical inspection non of them is shorted with the next one also
      What could cause tps to overheat as VREG3 & VREG5 are the only outputs now and non of them is shorted?

      Comment

      • caspian
        Badcaps Legend
        • Oct 2015
        • 1589
        • Laptop

        #4
        Re: tps51225c issue

        Vin may be still shorted.
        how much resistance-to-gnd is on Vin?
        is there any voltage on PL100 and PL101?
        Last edited by caspian; 10-27-2017, 07:14 AM.

        Comment

        • rookieme
          Badcaps Veteran
          • Oct 2014
          • 396
          • Greece

          #5
          Re: tps51225c issue

          vin~ 73kohm
          PL100 & PL101 are both 0V as I have all four mosfet removed

          Comment

          • caspian
            Badcaps Legend
            • Oct 2015
            • 1589
            • Laptop

            #6
            Re: tps51225c issue

            it is normal for tps51225 to get a bit warm.
            how much voltage is on DC-jack?

            Comment

            • rookieme
              Badcaps Veteran
              • Oct 2014
              • 396
              • Greece

              #7
              Re: tps51225c issue

              dc-jack gets 19,6 V
              tps51225 get hot enough so you cannot hold your finger on it, somehow it manages to get that way for a long time without get burned [gives stable 5V and 3V at VREG3 &5]

              Comment

              • mielta
                Badcaps Veteran
                • Apr 2015
                • 368
                • Germany

                #8
                Re: tps51225c issue

                Hi
                remove PL100 and PL101 und check short to ground
                give with a laboratory power supply 3v behind PL100 and check amp

                Comment

                • rookieme
                  Badcaps Veteran
                  • Oct 2014
                  • 396
                  • Greece

                  #9
                  Re: tps51225c issue

                  Even with both coils removed the regulator still run hot to touch.
                  Currently I don't have such power supply, the resistance to ground at the output of PL100 is 15 kohm but at PL101 is only 37 ohm.
                  The fact is that when I give power at that linw with the help of a l-ion battery nothing gets hot.



                  update:
                  I removed pu800 and it's upper mosfet any short at 5V line is gone
                  tps still runs hot
                  Last edited by rookieme; 10-31-2017, 08:47 AM.

                  Comment

                  • mcplslg123
                    Badcaps Legend
                    • Jun 2015
                    • 7262
                    • india

                    #10
                    Re: tps51225c issue

                    Try replacing ene 9012. Will require programming after install with programmer like RT809 or svod etc.

                    Comment

                    • caspian
                      Badcaps Legend
                      • Oct 2015
                      • 1589
                      • Laptop

                      #11
                      Re: tps51225c issue

                      I think you measured resistance-to-gnd on Vin by mistake. please measure it again to make sure.
                      if it did not solve the problem, the next step will be removing PL102. then check whether TPS gets hot or not. then, measure resistance-to-gnd on the two pads under PL102.

                      Comment

                      Related Topics

                      Collapse

                      • OOF DIO
                        ASUS FX505DV no power shorted at PWM controller Pin 3 VREG3 TPS51225C, need pinpointing of the short.
                        by OOF DIO
                        (If anyone has a functional boardview file of FX505DV/DU that would be helpful)
                        (Had 3 problems, now just 1)

                        I have no experience or knowledge and usage of tools to repair devices besides the entire past 12-10 days of researching, watching YouTube repair videos and troubleshooting this laptop motherboard. ChatGPT was used as a guide to ask questions.
                        I used boardviews of mostly FX505GD-M, and some FX505DU, FX505DD. Used schematics of FX505DU.

                        I had originally intended to replace the BQ24780s first (due to previous battery removal while benchmarking) but I...
                        04-19-2025, 05:03 PM
                      • rounin
                        MacBook Air A2337 (820-02016) USB-C Port Issue – Only Works in One Orientation (CC Line Problem?)
                        by rounin
                        Hi everyone,

                        I'm working on a MacBook Air 2020 (A2337, board 820-02016) and running into a strange USB-C issue. I've gone through quite a bit of testing and part replacement, but I'm stuck — hoping someone here can shed some light.

                        🛠 Original Issue
                        The machine initially wouldn't negotiate 20V over USB-C — stuck at 5V.
                        Diagnosis showed PP1V5_UPC0_LDO_CORE shorted to ground.

                        I replaced U3100 (UF400) using a donor board (A2179), and the machine powers on fine now.

                        ⚠️ New Problem: One USB-C Port Only Works in One Orientation...
                        04-19-2025, 01:18 AM
                      • ugamazing
                        Three 820-01700 32GB Logic Boards Same Issue: Won't Wake From Hibernate
                        by ugamazing
                        I have three identical-spec 820-01700 boards (2.6/32/512), and ALL THREE boards came to us with the same fault, from different sources: The boards don't wake from hibernation with the keyboard or lid, they ONLY wake when you press the power button. I understand this is a very minor issue, but the boards must be fixed!

                        We will of course begin with the obvious (checking lid signals), but I couldn't help but notice these three boards were all 32GB variants. Has anyone noticed an issue relating to these 32GB boards in particular? I of course don't think it's a RAM issue, but it's bizarre...
                        12-17-2024, 07:05 PM
                      • Simone Vergani
                        Alienware 15 R2 Service Tag: DL7NN32 ISSUE (Battery is not charging)
                        by Simone Vergani
                        Hello everyone,

                        I'm experiencing an issue with my Alienware 15 R2 (Service Tag: DL7NN32). The laptop works perfectly when connected to the AC adapter — it powers on and functions normally. However, the battery does not charge. If I disconnect the DC adapter, the laptop shuts down immediately, as the battery is at 0%. I have replaced the battery with a new compatible one, but the issue persists. I also replaced the AC adapter with a compatible one, but the battery still doesn't charge.

                        To assist with troubleshooting, I'm attaching two power circuit schematics:
                        • Power
                        ...
                        03-05-2025, 02:25 PM
                      • wizard13
                        Dynabook Satellite Pro C50D-B-100 - BIOS Issue, Black Screen
                        by wizard13
                        Hello everyone,

                        I am experiencing a BIOS-related issue with my Dynabook Satellite Pro C50D-B-100. When I power on the laptop, the screen stays black, and there is no response from the system. I suspect a corrupted BIOS.

                        I have checked the forum and the available documentation but could not find a solution specific to my issue.
                        • Brand & Model: Dynabook Satellite Pro C50D-B-100
                        • Part Number (P/N): PYU13E-00C00PFR
                        • Serial Number (S/N): 22028896H
                        • System Configuration (SC): A1PYU13E1127
                        • Motherboard Model: IP3_ACN16_MB_V21_20211222A
                        • Power Input: DC 19V –
                        ...
                        02-28-2025, 02:43 AM
                      • Loading...
                      • No more items.
                      Working...