QqEEH - Lenovo NM-D522

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • bociub
    Member
    • Dec 2023
    • 32
    • UK
    #1

    QqEEH - Lenovo NM-D522

    Hi There

    So I am looking for a part. Namely, a QqEEH. I beleive this is responsible to create the 3.3 power rail, but on my motherboard it is shorted to the ground. injecting 1 volt into the 20 volt power rail the IC heats up. Around the IC almost everything is shorted to the ground,
    Anyone knows what this little controller chip supposed to be?

    Thanks,

    Attached Files
    Tags: None
    • mon2
      Badcaps Legend
      • Dec 2019
      • 14673
      • Canada
      #2
      From the above database of parts:

      Qq*** SY8386BRHC (EL432 EL532 LA-H131P)

        Comment

        Previous template Next

        Related Topics

        Collapse
        • mkdj
          Lenovo Thinkpad L480 : 3VALW rail shorted to ground, but I can't find the shorted component
          by mkdj
          Dear all,

          Laptop is Lenovo Thinkpad L480 (boardview can be found in this badcaps topic). When pressing the power button the LED power light turns on, but nothing else happens.

          I removed the motherboard, checked for shorts on the main inductors. I found that there is a short to ground on the +3VALW_P rail (@PL201). I soldered a wire on the PL201 inductor, and I injected up to 1.3V with my power supply. Current drawn is approximately 3.2A.

          I used a small thermal camera to locate the shorted component. But nothing on the board heats significantly, except the...
          08-11-2025, 04:55 AM
        • mkdj
          Acer TravelMate P214 - N19Q7 main power rail shorted to ground
          by mkdj
          Dear all,

          I have taken out the motherboard of a Acer TravelMate P214. There is a short to ground on the main power rail (19V). I don't have the schematics or boardview for this board (DAZ8IMB1AA0 REVA). But I have found 4 MOSFETS close to the main power rail : 2 N-Channel and 2 P-Channel.

          I have checked resistance across each of the 4 MOSFETS. I have the following readings:
          Both N-Channel Mosfets: nothing odd

          P-Channel MOSFET number 1:
          source - drain : 117 kOhm
          source - gate: 96 Ohm
          gate - drain: 117 kOhm

          P-Channel MOSFET...
          08-20-2025, 06:08 AM
        • coasterghost
          Lenovo T14 Gen 2 Type 20XK Model 20XK0069US Odd Charging Issues
          by coasterghost
          For Badcaps Readers, Please note that I am hopefully going to present this same message to Lenovo to see if they have any insight to the matter as well and figured to share the entirety here for clarification. The System is out of warranty as it is but does have the option to have it extended.

          Model Information: T14 Gen 2 (Type 20XK, 20XL) Laptop (ThinkPad) - Type 20XK - Model 20XK0069US
          Board: T14 Gen 2 (Type 20XK, 20XL) - Type 20XK.

          System Hardware:
          Processor: AMD Ryzen 7 PRO 5850U
          Memory: 1x 16GB DDR4 3200 (Soldered on Board); 1x Crucial 32GB DDR4...
          09-08-2025, 10:46 PM
        • lefetylorant
          Lenovo Thinkcentre tiny M90Q gen 1 - no 12V rail
          by lefetylorant
          Hello Everyone,

          Long story short, I got this unit for very cheap.
          I've started to experiment with it's BIOS, as I did before successfully with an M900. However my very bad quality SOIC clip broken while dumping of the biosof and it must have damaged something on the panel, because it does not turn on, and does exactly nothing when powered. The maximum voltage that could have affected something is the 3.3 or 5v from the IC clip, because the unit was not powered while the bios dumping was in progress.

          I've performed some measurements:
          - 20V rail perfectly...
          09-14-2023, 05:05 AM
        • Nagy Daniel
          Lowest possible resistance on laptop motherboard rail - Guide Table request
          by Nagy Daniel
          Hi, I'm Daniel, and I'm new to the world of repairing motherboards.

          I would like to create a table, or more likely a guideline about the voltage rails and their possible resistance rail.

          I know that the motherboard design has a very big depend on the rail's resistance, but I would like to know what is the smallest value for a rail that can be acceptable. For example, I heard that some new gaming motherboards can have 0,5 Ohm resistance on the GPU rail, but on an older type, it could be a sign of a shorted GPU rail.

          So, I generated a table with AI so I can...
          03-04-2025, 08:24 AM
        • Loading...
        • No more items.
        Working...