Nintendo Switch no power, charing ok

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • reset1986
    Badcaps Veteran
    • Dec 2014
    • 308
    • italia
    #1

    Nintendo Switch no power, charing ok

    hi, i have this nintendo switch that does not turn on, the charging circuit is ok, i measure 4.20v at the battery connector, i have already replaced the m92t36 and PI3USB chips, usbc socket and cpu reflow,
    the battery is charged with 4.10 V and I measure about 4 V at the switch power pin,

    the console is always off it does not react to anything, it charges but remains off, do you know what I can control? thank you
    Tags: None
    • Cyo
      New Member
      • Sep 2020
      • 3
      • United States
      #2
      Re: Nintendo Switch no power, charing ok

      Checkout tronixfix on YouTube. He has dealt with switches with this exact issue.

        Comment

        • vinceroger69
          Badcaps Legend
          • Mar 2012
          • 6714
          • uk
          #3
          Re: Nintendo Switch no power, charing ok

          Maybe worth joining this facebook group if your not already a member some very good switch repair tips have been posted https://www.facebook.com/groups/console.repair.legion

            Comment

            Previous template Next

            Related Topics

            Collapse
            • Document Archive
              Acer Switch Switch V 10 SW5-017P Hybrid (2-in-1) V 10 Specification for Upgrade or Repair
              by Document Archive
              This specification for the Acer Switch Switch V 10 SW5-017P Hybrid (2-in-1) can be useful for upgrading or repairing a laptop that is not working. As a community we are working through our specifications to add valuable data like the Switch V 10 SW5-017P boardview and Switch V 10 SW5-017P schematic. Our users have donated over 1 million documents which are being added to the site. This page will be updated soon with additional information. Alternatively you can request additional help from our users directly on the relevant badcaps forum. Please note that we offer no warranties that any specification,...
              09-06-2024, 05:30 AM
            • Tomylee
              No LCD image after connector replacement – lifted components and damaged resistor (Nintendo Switch Lite HDH-CPU-02)
              by Tomylee
              Hi everyone,

              Sorry for the person who’s going to read all this !
              I'm on a Nintendo Switch Lite, motherboard HDH-CPU-02.

              While replacing the left joystick, I had to remove the motherboard to access the connector underneath. When I lifted the LCD connector latch, it broke (the plastic had become brittle over time), so I replaced the entire connector.

              During the desoldering of the LCD connector using hot air, three small components located just below the connector (likely 0402 capacitors) came off and remained stuck to the bottom of the...
              07-11-2025, 11:52 AM
            • tommy97
              Nintendo Switch Oled - Joy con charging
              by tommy97
              Hi everyone,

              I'm having an issue with a Nintendo Switch OLED that suffered liquid damage. After a full cleanup and replacing the Joy-Con rails and joysticks, everything was working fine for about a week. However, now the Joy-Cons won't charge or connect again.

              I tested with a second set of Joy-Cons, and the issue persists. Measuring the voltage on the connector shows 3.7V instead of 5V, which I believe should be the correct value.

              Any insights or suggestions on what could be causing this?
              ​
              03-17-2025, 06:30 AM
            • fab13
              Nintendo Switch lite shuts down after nintendo log and replaced M96T36o
              by fab13
              Hello everyone

              After checking the defective USB-C port and close to a short circuit on the M96T36 chip (8ohm) I have changed both components.
              I specify that there is no other short circuit or heating component(Vu thermal camera)

              First, the problem arises: Error 2101-0001 after the start-up screen ("Nintendo" logo), poor soldering.

              Secondly, I install a new M96T36 and the problem I have is a brief display of the "Nintendo" logo (no short circuit, no sure charge chip, no sure charge port, no sure charge management chip percentage)....
              08-23-2023, 10:54 AM
            • CraigR
              Nintendo switch drown victim help needed
              by CraigR
              Nintendo switch with some water damage came in and I need a picture of components and values on both sided down by the fuel gauge ic. If anybody would have a pic or could help me out it would be greatly appreciated!...
              08-13-2024, 12:22 PM
            • Loading...
            • No more items.
            Working...