Re: PS5 BLOD- CFI-1115A Disc Version- Board= EDM-020
Update: As a last ditch effort i pulled the New wifi module off to check diode readings without it. All diode readings now match a known good board. Working on getting another wifi module. Stay tuned.
-
Re: PS5 BLOD- CFI-1115A Disc Version- Board= EDM-020
Resistor was 200k. Still chasing root of problem.Leave a comment:
-
Re: PS5 BLOD- CFI-1115A Disc Version- Board= EDM-020
Anyone know the value of this resistor on the 1.8v rail of the edm-020 board? Showed low resistance to ground and want to replace.Attached FilesLeave a comment:
-
-
Re: PS5 BLOD- CFI-1115A Disc Version- Board= EDM-020
A2 chip did not rectify the issue. Replaced all caps under wifi module. Some caps on this line are still reading short to ground. Maybe I have a bad wifi module? Not sure where the 3.3v and 5.0v rail are created. Thanks Sony lolLeave a comment:
-
Re: PS5 BLOD- CFI-1115A Disc Version- Board= EDM-020
I am hoping this works per the a2 chip's datasheet. https://www.mouser.com/ProductDetail...G5yjipLg%3D%3DLeave a comment:
-
-
Re: PS5 BLOD- CFI-1115A Disc Version- Board= EDM-020
maybe if you check the size in mm and then look at inductors at digikey you can get an ideaLeave a comment:
-
-
Re: PS5 BLOD- CFI-1115A Disc Version- Board= EDM-020
Can you post your dump of your board ? (EDM-020)Leave a comment:
-
-
Re: PS5 BLOD- CFI-1115A Disc Version- Board= EDM-020
The issue Phil has here sounds like my issue now that the southbridge is back to normal. Just watched his vid here tonight. This PS5 may have been trolling me with the Southbridge issue. https://youtu.be/IevHM3oDUvg. Going to follow Phil's troubleshooting and see if we can land this plane haha. Still need the fuse and cap values he replaces here but it's a start.Leave a comment:
-
Re: PS5 BLOD- CFI-1115A Disc Version- Board= EDM-020
well 0402 is a lot smaller than 0603, so get the correct size or soldering it in wont be easyLeave a comment:
-
-
Re: PS5 BLOD- CFI-1115A Disc Version- Board= EDM-020
either will handle more that a ps5 has in itLeave a comment:
-
-
Re: PS5 BLOD- CFI-1115A Disc Version- Board= EDM-020
0402 vs 0603 you can check with a vernierLeave a comment:
-
Re: PS5 BLOD- CFI-1115A Disc Version- Board= EDM-020
To be honest i dont know what I need. Just going by what i was told.What would be the best way for me to test. I was also told the fuse is probably a 0402 fast blow. Instead of 0603 slow blow. Frustrating not having a schematic
Leave a comment:
-
Re: PS5 BLOD- CFI-1115A Disc Version- Board= EDM-020
thats fine if it is 3a you needLeave a comment:
-
Re: PS5 BLOD- CFI-1115A Disc Version- Board= EDM-020
So this would work right?
https://www.digikey.com/en/products/...00-TM/15204247Leave a comment:
-
Re: PS5 BLOD- CFI-1115A Disc Version- Board= EDM-020
Exactly "stj".
Diif, Sorry was a horrible picture after the downsize for upload. I snapped a new one. Here you go. "T"Attached FilesLeave a comment:
-
-
Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.
Upon bringing it home and plugging it up, it showed a standby light.
I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.
The screen seems to blackout and stay black, but with a flashlight I can see the display.
With my Playstation 4 connected via HDMI, and running a game I can hear sound.
Assuming... -
Hi, this is my personal laptop, which the original board (lets call it Board A) blew up PU8700 (TPS51486), making a hole on the board, i had left the laptop at my desk one day with the battery fully charged and didn't touch it for a week, but when i tried to turn it on it didn't
Thought the battery was dead, so i plugged in the charger then tried to power on, the power LED blinked once, charged LED still orange, unplugged the charger, plugged in again and I noticed the "magic smoke" smell, so i unplugged the charger, removed the back cover and saw the blown IC (the "magic... -
Good Afternoon fellas,
Issue:
Disc is showing as not supported when a disc is put in.
Here's what I've done, you can skip this if you just wanna know the question:
- replaced with a disc drive from a donor ps5 (honestly questionable if this is known to work)
- reflowed the disc drive connector
-reflowed the chip in question (shown on image)
- I will say this console was very dusty so it's conceivable that it got so hot that it made the chip joints cold and potentially other things on the board
Question:
I... -
Hi There,
This TV was auto switching off after few seconds with some vertical lines on the screen, so got a new TCON board and replaced it.
After replacing the TCON board it was working fine and i set it up with everything, used for few hours, then had the bright idea to update the software on it. During the update process, TV switched off and now no audio or video. No relay switch sound.
More Details
TV Model - LG OLED77G1PUA
Got the same exact TCON board from TVPartsToday and replaced it. But didnt transfer the EPPROM data (didnt... -
Hey guys great forum glad to have found it. I bought a Sony XBR 65X900C cheaply because it didn't work. No signs of life at all not even a light/led. All I hear is a brief high voltage sound when I throw the power to it.
Didn't see any obvious signs of damage so right away started checking voltages. This is what I see:
Power Board Connector that goes to Main board
CN6401
Pin 01 NC
Pin 02 NC
Pin 03 "BL_ON": 0V
Pin 04 "N/C"
Pin 05 "STBY 3.3V": 3.5V
Pin 06 "GND": N/C
Pin 07 "AC_OFF"...
Leave a comment: