Bad new cap

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Nemo1956
    New Member
    • Jan 2017
    • 5
    • Thailand

    #1

    Bad new cap

    I have just repaired a valve radio that need a new capacitor. I replaced it as it had gone open so I put a new one in only to have it go pop some 2 minutes later. I found that the case had a resistance of only 23 ohms to one of the pins.
    Not good at all.
    Have anyone else seen this?
  • eccerr0r
    Solder Sloth
    • Nov 2012
    • 8688
    • USA

    #2
    Re: Bad new cap

    Did you put in a New Old Stock capacitor or a new modern capacitor?

    If the former, you may have needed to reform it before using it.

    If it's the latter, it probably was either over voltage or reverse biased.

    Comment

    Related Topics

    Collapse

    • shelby5041
      clock radio / radio lifespan?
      by shelby5041
      hi
      ive got a modern digital clock radio approx 15yrs old

      my question is how long can a clock radio or a simple radio last ss farcas operating hours?

      since elec components have limited hour lifecspan i would imagine the radio or clock radio would eventually fail.

      the reason i ask is because i have my clock radio on radio function 24/7 for the past 7 years and its still working fine....i leave the radio on ..never turn off past 7years...thats approx 60000 hours

      it uses very little power just a few watts i would imagine that may have something...
      09-14-2024, 03:30 AM
    • praveenramavath
      Majority PETERHOUSE GRADUATE Internet Radio (Auna Silver Star) - Stuck at boot "Welcome" Screen
      by praveenramavath
      Hello All,

      I have an issue with my Majority PETERHOUSE GRADUATE Internet Radio, it keeps rebooting at the boot logo Welcome screen. I have an another forum active in other website but due to lack of response I am posting the same here. I am positing a link below that has pictures including all the troubleshooting I have tried, appreciate if someone can take a look and give me any suggestions.

      https://www.hifivision.com/threads/m...-screen.98243/


      Troubleshooting Summary: Majority Internet Radio - Flash Chip
      ...
      04-26-2025, 09:08 AM
    • Document Archive
      HP EliteDesk 800 G3 + OfficeConnect OC20 2x2 Dual Radio 802.11ac (RW) Access Point EliteDesk 800 i7-7700T Specification for Upgrade or Repair
      by Document Archive
      This specification for the HP EliteDesk 800 G3 + OfficeConnect OC20 2x2 Dual Radio 802.11ac (RW) Access Point can be useful for upgrading or repairing a desktop PC that is not working. As a community we are working through our specifications to add valuable data like the EliteDesk 800 G3 + OfficeConnect OC20 2x2 Dual Radio 802.11ac (RW) Access Point boardview and EliteDesk 800 G3 + OfficeConnect OC20 2x2 Dual Radio 802.11ac (RW) Access Point schematic. Our users have donated over 1 million documents which are being added to the site. This page will be updated soon with additional information....
      09-12-2024, 02:00 PM
    • Omron
      Kenwood KDC 3051G Car Radio permanently stuck in Demo Mode please help
      by Omron
      Hello Guys! I have trouble with my car radio Kenwood KDC 3051G I hope someone more knowledgeable can help me, I tried everything in my power that I stumbled upon online.

      My radio is permanently in demo mode, it says Press Volume Knot Cancel Demo and when I press it nothing happens.

      - Tried to unplug radio and plug it back in into power,

      - Tried to reset radio by holding reset button key for 5,10,30 seconds while in power and without power, plugging it back in, it wouldn't work.

      - Tried to hold 3,6 while turning it back on and then pressing 1,2...
      05-23-2024, 01:27 PM
    • TinkerTron
      Schematic vs. Reality: Where Are the Resistors on My Sharp Clock Radio? Model FY-70CH
      by TinkerTron
      Hey everyone,

      I'm currently working on a mid-70s Sharp Electronic Digital Clock Radio, Model FY-70CH. I found the service manual online, printed it out, and have been studying it for a while. My main reasons for tackling this are: (1) I want to learn electronics and figured I'd start with something I had on hand, and (2) I want to fix its issues. Right now, the radio sounds awful, has about 5V DC at the speaker terminals, and the alarm time setting doesn't work. But I'm not asking how to fix these problems.

      Instead, here's what's been bugging me so far:
      The schematic...
      03-06-2025, 02:03 PM
    • Loading...
    • No more items.
    Working...