SAS IO Programmer v.4.0 defect

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Repdata
    Senior Member
    • May 2020
    • 67
    • Deutschland

    #1

    SAS IO Programmer v.4.0 defect

    HELLO
    I have a SAS IO programmer version 4.0 here, which recognizes the FTDI when plugged into the USB
    But it reports that the programmer is not found.
    I think the firmware on the Atmega 328p is buggy.
    Does anyone know where I can get the hex file from??
    Attached Files
  • lotas
    Badcaps Legend
    • Jan 2016
    • 4456
    • Russia

    #2
    Re: SAS IO Programmer v.4.0 defect

    This happens if the FTDI chip itself is not original (fake)! And because of this, the official drivers do not get up.
    http://www.leoniv.diod.club/articles...l/ft232rl.html
    Last edited by lotas; 06-17-2023, 03:09 AM.

    Comment

    • SMDFlea
      Super Moderator
      • Jan 2018
      • 20276
      • UK

      #3
      Re: SAS IO Programmer v.4.0 defect

      Originally posted by Repdata
      I think the firmware on the Atmega 328p is buggy.
      Does anyone know where I can get the hex file from??
      https://www.badcaps.net/forum/showth...SAS+programmer ,post #13 might help, contact the cloners support.

      .
      All donations to badcaps are welcome, click on this link to donate. Thanks to all supporters

      Comment

      • stormanimal83
        Senior Member
        • May 2014
        • 74
        • Germany

        #4
        Re: SAS IO Programmer v.4.0 defect

        Originally posted by SMDFlea
        https://www.badcaps.net/forum/showth...SAS+programmer ,post #13 might help, contact the cloners support.

        .
        no good news for your @repdata... lotas was right warning you about clones (not only ftdi) in this case the whole board is a clone but using software of a russian programmer without permission... only reads 128KB even if the chip is 256KB.... throwing this one in the bin and buying an original would be the best solution for you...
        Last edited by stormanimal83; 06-18-2023, 01:27 AM.

        Comment

        Related Topics

        Collapse

        • STKR123
          The right BIOS Programmer - The right software (HP Elitebook 820 G1, 840 G2) no soldering, EC, DMI, ME
          by STKR123
          Greetings badcaps community,

          I havent done this for a long time and want to start it all again, after some evil and annyoing illness.
          So I apologize in advance, if some phrases might sound a bit like gibberish or illogical to you.

          Im trying my best to fully describe what I plan to achieve and hope I was choosing the right sub-forum for my new adventure.

          I have a Elitebook 820 G1 and a Elitebook 840 G2 here.

          These ask for a password when entering the BIOS, but boot just fine from the internal SSD.

          I learned that desoldering...
          10-29-2024, 06:03 AM
        • Teeheeze
          RT809H Programmer Firmware Corrupted
          by Teeheeze
          This is a shot in the dark, but I was just using my RT809H programmer and it got stuck in a certain state so I power cycled it. Now, the device LED just flashes quickly and does not connect to the software. I've tried to update the BIOS of it and it fails. I went so far as to remove the ROM from the programmer itself but it's some weird chip (I believe ATMEL, but I can't find any datasheet on it) so I've been unable to read the BIN from it w/ my other programmer. Chip has ATMLHC4C56BM CN written on it (I think). I'll upload an image. I have the programmer's BIN ready to program it manually. Anyone...
          02-13-2025, 04:51 PM
        • H34TO
          ITE IT8390 (IT8390E-256) programmer "ITE Download Board 4" user manual + firmware, flashing ITE ECs on the cheap
          by H34TO
          Recently I've gotten into EC flashing due to my broken laptop(s) and started frantically searching methods for flashing the IT5571E-128 chip on the cheap(due to me beaing a student and not having a job) and noticed that ITE newer chips can be flashed via ISP (In-System Programming) either via SMBus or the KBC (EPP - Enhanced Parallel Port) interface. While these can be achieved with programmers like SVOD4/3 or the RT809H/F those options are WAYYY out of my budget so I was horrified. But recently I stumbled uppon some programmers on aliexpress that claim they can program a variety of ITE chips...
          06-17-2025, 07:17 AM
        • vinceroger69
          TL866CS MiniPro EPROM programmer software
          by vinceroger69
          Hi has anyone got the latest software for the TL866CS MiniPro EPROM programmer version 03.2.86 is installed now i have tried the update site in the programmer software but it wont connect to their website i am running windows 10

          Edit found this site programmer works now http://www.xgecu.com/EN/Index.html
          09-03-2024, 06:21 AM
        • EazyBone
          EMMC programmer questions
          by EazyBone
          Looking to up my game a little bit, but these programmers seem a bit daunting.

          Trying to get a device for EMMC repair, and it's very difficult to lookup all the words to find if I'm on the right track lol.

          Trying to reprogram EMMC on Sony/Hisense mainly but would like to hit a few other brands.

          My question is would either of these work? And is there a specific card reader I need for TV emmc? There is like 10-40 additional pieces that I can get but not sure what I actually need for my application only.

          I may do eeprom as well. Can someone point...
          04-21-2024, 08:18 AM
        • Loading...
        • No more items.
        Working...