Philips 220CW9 no image, power LED cycles toghether with a high pitch whine

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • sequille
    Member
    • Feb 2010
    • 33
    • United Kingdom
    #1

    Philips 220CW9 no image, power LED cycles toghether with a high pitch whine

    I disconnected the LCD panel, left only the logic board and backlight connected and it stays on (white screen). The moment I connect the LCD panel it starts cycling on-off, together with a (not very loud) squeal that stops when the LED off.
    The LCD panel is a Samsung LTM220M1-L01, if this is relevant.
    Tags: None
    • R_J
      Badcaps Legend
      • Jun 2012
      • 9558
      • Canada
      #2
      Re: Philips 220CW9 no image, power LED cycles toghether with a high pitch whine

      How about some good quality pictures of the power supply etc. and some voltage readings so we can see what you have, It sounds like the power supply can't supply the current to run the panel.

        Comment

        • dskall
          Badcaps Legend
          • Oct 2016
          • 2905
          • usa
          #3
          Re: Philips 220CW9 no image, power LED cycles toghether with a high pitch whine

          Try disconnecting t-con to panel board cables one at a time and see if one side is causing problems.
          I assume no responsibility for any stupid suggestions I might post.

            Comment

            • sequille
              Member
              • Feb 2010
              • 33
              • United Kingdom
              #4
              Re: Philips 220CW9 no image, power LED cycles toghether with a high pitch whine

              Turns out that, against all appearances, it was a capacitor. Ended up replacing them all so that i wouldn't have to go through disassembly again.

                Comment

                Previous template Next

                Related Topics

                Collapse
                • G33RT
                  Philips 8200 series 65PUS8204/12 stuck at Philips Logo
                  by G33RT
                  Philips 8200 series 65PUS8204/12 stuck at Philips Logo, it does not reboot it just stays on the logo.

                  It does power up when pressing the power button.

                  I already try the power button while plugin the plug with no result.
                  Also put the latest firmware autorun-TPM191E_R.001.004.100.000.upg on a MBR/FAT32 USB stick at USB port2 with no result either.

                  Could this be an PSU or eMMC issue ?
                  07-19-2025, 03:43 AM
                • karatzdi
                  Denon AVR 1908, High pitch noise on Surround back Left channel after long overhaul
                  by karatzdi
                  Hello,

                  I know some might say... just buy another one. Sell it as parts..!

                  So had this AMP for quite some time. Recently I saw light smoke coming out of the AMP. Had my fire extinguisher close by. Just kidding. Turned immediately all devices off from mains.
                  Let things cool a bit, and opened up the amp device. I clearly saw on the main board which hosts the 5X amp (5.1), 3 10 ohms 1W resistors had their leads looking black, while the rest of the remaining 2 x 10 ohms were brownish as being installed from factory.

                  Spent some time downloading the Service...
                  06-11-2024, 08:38 AM
                • double_DD
                  Philips curling iron - is this a common AC cable?
                  by double_DD
                  Hi all,

                  Wife has 2 Philips hair curling irons half defective - after learning how they're supposed to work and testing them, it turned out that both have defective power cables, and both on the same place; broken wires due to wire bending.
                  As they were both relatively easy to disassemble, and cables are plugged not soldered (as they can rotate in the handle), I was sure it would be easy to find replacements. But - NO! I'm unable to find anything similar on ebay or Aliexpress.

                  Not sure if this is something Philips proprietary, or a standard, but the cable plug...
                  08-18-2025, 10:04 AM
                • janos6662000
                  Philips 47PFS7509/12 LCD TV problem
                  by janos6662000
                  Hi

                  I have here a Philips 47PFS7509/12 LCD TV which came to me with a weird problem : without signal i could access menu, make a factory reset, access menus, etc.
                  When i applied cable signal to check image, i had normal picture, but TV was restarting.
                  I downloaded original firmware and applied the update, but the problem remained.
                  From a colleague i received a "factory package software" which is a lot bigger.
                  I made another firmware update, but still did not solve the problem.
                  Somewhere on the way the error got worse, because at the moment the...
                  08-12-2025, 12:54 PM
                • Gjackson
                  ADP-160FR ps4 slim PSU, shuts down under load and has severe coil whine.
                  by Gjackson
                  Hi all, the PSU originally had a no 12v issue where as soon as I bridged the 5v standby to the ACDC_stby the psu would switch itself off completely. I monitored the voltage on the main filter caps while doing this and saw that the PFC was bringing the voltage up to around 360vdc before shutting down. Given that I saw that as a little low I replaced the PFC feedback resistors from a donor PSU and that got it to power on, without a load no coil whine is present and there is a stable 12v however as soon as I put it in the PS4 it starts whining really badly, however 12v remains stable but after a...
                  01-13-2024, 10:34 AM
                • Loading...
                • No more items.
                Working...