Hi Guys
Can someone help me to identify value of this resistor R453 located on Amp PCB.
Many thanks
Can someone help me to identify value of this resistor R453 located on Amp PCB.
Many thanks
-
-
Re: Pioneer VSX824/529 burnt out resistor R453
You will get a lot more help by uploading good clear pictures of what we are dealing with.Never stop learning
Basic LCD TV and Monitor troubleshooting guides.
http://www.badcaps.net/forum/showthr...956#post305956
Voltage Regulator (LDO) testing:
http://www.badcaps.net/forum/showthr...999#post300999
Inverter testing using old CFL:
http://www.badcaps.net/forum/showthr...er+testing+cfl
Tear down pictures : Hit the ">" Show Albums and stories" on the left side
http://s807.photobucket.com/user/budm/library/
TV Factory reset codes listing:
http://www.badcaps.net/forum/showthread.php?t=24809 -
Re: Pioneer VSX824/529 burnt out resistor R453
You would need to locate the manual for the VSX-1024-K, or you could locate the same resistor in one of the other channels to find the value.Comment
-
Re: Pioneer VSX824/529 burnt out resistor R453
A picture of the board up and down would help. Theres identical resistors in every channels.Comment
-
I've got a 240v LED uplighter which isn't working. Pulling it apart shows a clearly burnt resistor on the circuit board, and I'm hoping some of you will have suggestions on what to replace it with. First, here are some photos. Power comes in, through the fuse and choke, then through the big blue variable resistor labelled B500K (ignore the similar blue component at the bottom - it's a simple switch for an attached reading lamp). It then passes through the burnt resistor (or at least did once), through diac DB1 and the unburned 30 ohm resistor to the gate of the triac.Now I assume there's a simple... -
Hello Badcaps!
I am trying to troubleshoot my Allen & Heath Xone:02 DJ mixer. I have had this for somewhere close to 20 years and have played music through it in one form or another pretty much every single day since I've had it, though these days it's usually from a wireless streaming receptacle (Apple Airport) more than the turntables that are also connected to it.
This week my music stopped working, and after a bit of a wild goose chase, I realised my mixer was dead. I checked the 500mA fuse in the device beside the power supply and found it was blown, so I replaced... -
Hi
I have an Ersa rds 80 soldering station which has developed a fault and just showing err on display
I have found a burnt resistor on pcb can anyone help me identify this resistor if you have a circuit diagram or similar unit
The printed circuit board markings are rd80 ver 2.0 and the resistor in question is R6
Many thanks... -
First post -Intel NUC 10i5 -BXNUC10i5FNH not powering on -IC burnt- request for IC details/datasheetHi all,
I came across this very active forum with knowledgeable folks on electronic circuits and components, while google searching for the details of my burnt IC marked 7603 in Intel NUC board. I joined this forum today and this is my first post here.
I recently got an Intel NUC 10i5 and had installed Linux Mint and was using it for about a month when it died suddenly and did not power up after that.(Power Adaptor is ok). When I opened the NUC , there was a burnt IC marked 7603 (and ILCB in second line). I am unable to find the details/datasheet of this IC. I will be grateful if... -
Hi
I am trying to repair an ancient Dell 2209WA Monitor which suddenly shut off with a pop sound. On investigation found that one of the fusible resistors had blown. Further investigation identified multiple components as faulty because of which the fusible resistor blew. Please refer the attached circuit diagram showing the components that were found to be damaged.
1. FR950 - blown fusible resistor - 0.2 Ohm 1W
2. Q950 - shorted Q950 MOSFET - 650V 10A N Channel Mosfet
3. R835 - Blown Resistor - 20KOhm SMD resistor
4. D930 - Shorted Schottkey Diode...
Comment