Pioneer VSX-1021-k

Collapse
X
Collapse
 
  • Page of 3
  • Time
  • Show
Clear All
new posts
Previous 1 2 3 template Next
  • tibimakai
    Badcaps Legend
    • Jan 2012
    • 3680
    • USA
    #41
    Re: Pioneer VSX-1021-k

    Usually I measure the final transistors for short and the ones that are shorted, I just cut there legs. Than I reset the receiver and it should start right up.

      Comment

      • battlecat
        Member
        • Mar 2010
        • 18
        • South Africa
        #42
        Re: Pioneer VSX-1021-k

        Check your 5v power supply if this is the model with @ switchmode standby psu..

        Seem these amps are all flawed in some way..
        School fees paid as everyday is a learning curve.

          Comment

          Previous 1 2 3 template Next

          Related Topics

          Collapse
          • burntonnerings
            Pioneer VSX-1021 MCACC flashing, can't find problem
            by burntonnerings
            Have a Pioneer VSX-1021 that goes to MCACC flashing as soon as it is plugged in.

            If I enter release mode, it powers on, the screen display is correct, but then it shuts down and goes back to MCACC after a few seconds. I can shut it down to standby (w/o flashing MCACC if I hit the power button as soon as release mode finishes the boot sequence).

            Entering reset mode and executing a reset doesn't change this.

            I am unable to enter service mode to see the error counts - Enter + Power button doesn't do anything, whether from normal standby or from MCACC flashing....
            12-09-2023, 10:11 PM
          • ekozeko333
            [Help] Lenovo Yoga Slim 7-14ARE05 (DA0LS3MBAF0) – 25Q80DVN1G Flash Is All FF, USB-C PD Stuck at 5V
            by ekozeko333
            Hi all,
            I’m trying to recover a Lenovo Yoga Slim 7-14ARE05 with board DA0LS3MBAF0 Rev:F. I’ve run into an unusual issue where USB-C PD is stuck at 4.7–5V and the system won’t boot (keyboard lights flash briefly, then nothing).
            🔥 The Problem Started After Suspected ESD/PD Fault
            I experienced a power issue or ESD event through a USB-C charger
            After that, the NX20P5090 power switch was visibly burned and was replaced
            Now the PD controller always negotiates 5V @ 2A, even with known-good chargers
            🧠 What I’ve Done So Far
            Flashed...
            06-21-2025, 02:48 AM
          • corrize
            Nikon D800 camera - flash don’t work and capacitor don’t charge
            by corrize
            Hello, I'm stuck in troubleshooting…
            The flash system works like that : when the (mechanic) flash button is pressed, the flash mecanically pop up, and a circuit buck boost elevate 7v (batt) to 200-300v (?) for charging the big capacitor. And when the photo shoot button is pressed, the capacitor is discharged in the xeon light.

            In the D800, there is a first « power board » close to the battery. 2 wires (batt 7v) goes to another little « flash board ». I measured 7v, so ok.
            When I press the flash button, it's detected by the system, flash icon appear on LDC display....
            10-01-2022, 10:02 AM
          • spmetroil
            Request: SPI Flash BIOS Dump (Winbond 25Q128) for Dahua NVR4216-4KS2
            by spmetroil
            Hello,

            I am trying to repair a Dahua NVR4216-4KS2 that is not booting.
            The main BIOS/firmware is stored in an SPI flash EEPROM (Winbond 25Q128, labeled as U130 on the PCB).

            I have a CH341A programmer and I already attempted the following steps:
            1. Identified the correct chip (W25Q128, 3.3V SPI flash).
            2. Tried to read the contents with CH341A Programmer software. The dump seems corrupted and I often get the error: “Chip with the contents are in disagreement.”
            3. Compared several chip type selections (24Cxx and 25Qxx families) to confirm it is indeed a 25 series SPI
            ...
            08-19-2025, 09:23 AM
          • abajor
            Canon VIXIA HF S10 A read data from inernal flash memory.
            by abajor
            Hello I've had somebody bring in one of these charming little cameras to attempt retrieving data from the internal 32GB flash.
            Something is damaged inside the cameras lens assembly I can hear it clunking around and it has probably dislodged the sensor, powering up the camera gives a blank screen and the focus motor sounds like it's having a fit.
            The camera will not connect to a computer via USB in this state, I have no options no navigation, just power up and focus/zoom motor noises.

            I think my best shot is to figure out a way to read the internal flash memory outside...
            07-20-2024, 12:04 AM
          • Loading...
          • No more items.
          Working...