RCA RT2770 not working

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • MichaelFLA
    New Member
    • May 2013
    • 1
    • United States
    #1

    RCA RT2770 not working

    Hi! I'm new here, but am going to jump in feet first.

    I just picked up one of the above mentioned units and it isn't working. It has obviously been repaired (C220 & C212 are each two 2200uF 35V electrolytic caps in series).

    My issue is, there seems to be no voltage on the output side of transformer T102. Can anybody please tell the voltage I should be reading on each pin of this transformer?

    Any help would be greatly appreciated!
    Tags: None
    • Khron
      Badcaps Legend
      • Sep 2006
      • 1350
      • Finland
      #2
      Re: RCA RT2770 not working

      If it's anything like the receivers i've looked into, there should (also) be a smaller transformer on a "power pcb", that's handling the power during stand-by.

      When you press the "soft power" button, the microprocessor sends a signal to a relay on that power board, that switches the mains voltage to the primary of the big transformer, so...

      First step, get your hands on a service manual No sense in "flying blind" if that can be avoided
      Khron's Cave - Electronics - Audio - Teardowns - Mods - Repairs - Projects - Music - Rants - Shenanigans

        Comment

        • ben7
          Capaholic
          • Jan 2011
          • 4059
          • USA
          #3
          Re: RCA RT2770 not working

          Pictures would help us to help you quite a lot.

          Have you checked fuses too?
          Muh-soggy-knee

            Comment

            • budm
              Badcaps Legend
              • Feb 2010
              • 40746
              • USA
              #4
              Re: RCA RT2770 not working

              There are many thread on this RCA:
              https://www.badcaps.net/forum/search...archid=2708012
              Never stop learning
              Basic LCD TV and Monitor troubleshooting guides.
              http://www.badcaps.net/forum/showthr...956#post305956

              Voltage Regulator (LDO) testing:
              http://www.badcaps.net/forum/showthr...999#post300999

              Inverter testing using old CFL:
              http://www.badcaps.net/forum/showthr...er+testing+cfl

              Tear down pictures : Hit the ">" Show Albums and stories" on the left side
              http://s807.photobucket.com/user/budm/library/

              TV Factory reset codes listing:
              http://www.badcaps.net/forum/showthread.php?t=24809

                Comment

                Previous template Next

                Related Topics

                Collapse
                • MMH3
                  Dell Optiplex 5050 SFF - strange behavior and service_mode jumper not working anymore
                  by MMH3
                  Hello,

                  i have many 5050sff. all of them, and how i experienced over many years for all about 250 DELLs goin through my hands, are fully flashable and can be serviced in any way when the service_mode jumper is set.
                  Never ever i experienced problems with that.

                  Now i have one 5050sff machine, where this jumper isnt working at all.
                  I do not get the normal messge that the jumper is set when booting and a short test with FPT just confirms this. Everything is locked -->> EVEN for reading !?

                  The history of the machine is that i used it in my office...
                  03-23-2025, 09:28 PM
                • DynaxSC
                  GIGABYTE X299 AORUS ULTRA GAMING - SATA PORTS 4-7 NOT WORKING ???
                  by DynaxSC
                  Hi,

                  I have the above mentioned bord after repair, which was related to a lot of missing smd devices on the back of the board.
                  There were almost 20 devices missing, caps, resistors and some diodes/mosfets.
                  The board is generally working now, all PCIe ports are working, Windows installs normally.

                  However I have a problem with SATA ports 4-7 (the board has 8 SATA ports) - disks are not beeing recognized by the BIOS neither by Windows (which is usually normal in case BIOS does not recognize them).
                  The SATA 4-7 driver network is quite simple chipset<->buffers/drivers<->SATA...
                  03-10-2025, 12:27 PM
                • obelix24
                  Macbook Air 2020 (a2179) - touch id not working
                  by obelix24
                  Hi i have one Macbook Air 2020 where touch ID is not working (it's not scanning fingerprints). Touch ID was working before, there is no error message during scanning fingerprint it's just not scanning on screen you can see only fingerprint but there are no red updates as when it's working. Power button is working fine.

                  I've checked boardview and also schematics but i'm not able to find anything related to TouchID ... i have similar issue on a2338 where there was problem with PP3V0_TOUCHID​ and after replacing UT610 it was working but here i'm not able to find anything related to...
                  02-09-2025, 12:57 PM
                • hopkok
                  Lenovo Legion 16ITHg6 NM-D721, keyboard not working, LEDs too
                  by hopkok
                  Hi masters, I need your help.

                  I am working on Lenovo Legion 16ITHg6
                  Motherboard number NM-D721, no BV, no schematic but I am attaching very closes ones.

                  INPORTANT: My motherboard version is with IT8258 IC, that is controlling keyboard and RGB LEDs.

                  My problem is on UI142, +3VALW_AG is not stable, floating from 0V to 3,3V.
                  AGKB_PWR_EN_N signal is floating too (that is why+3VALW_AG not stable).
                  Power LED is not working as well, power button working well.
                  UI26 ??? is there any firmware too? Powered by +3VALW_AG.

                  Motherboard...
                  05-04-2025, 09:35 AM
                • dennis_elx33
                  3PHASE STEP-DOWN Transformer in Check
                  by dennis_elx33
                  Hello All,

                  i would like to post an interesting topic regarding 3-phase stepdown transformer which we suspect to cause an overcurrent (138A) which resulted to power tripped off of the HV power supply (80KV output).


                  Problem statement: Power tripped Off

                  Initial Problem: Found 2 IGBT and 2 rectifier diodes shorted (burnt).

                  Action Done:
                  1) Replaced the faulty parts with good spare.
                  2) Measured impedance of the 3phase input lines and found that L2 to L3 has 23.3ohm while other pairs are 51Kohm. This pins will...
                  12-02-2024, 06:52 AM
                • Loading...
                • No more items.
                Working...