philips ep2231 40 Q1 U7

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • samtron786
    Senior Member
    • Aug 2016
    • 165
    • germany
    #1

    philips ep2231 40 Q1 U7

    Hello,
    Which MOSFET do I have here? Is it an N-channel or a P-channel?
    I have two defective ICs, Q1 and U7. What are the names of these components?
    Thank you.​
    Attached Files
    Tags: None
    • CapLeaker
      Leaking Member
      • Dec 2014
      • 8214
      • Canada
      #2
      Q1 I read as marking 3G- = PNP transisor BC857C
      That’s not a mosfet

        Comment

        • samtron786
          Senior Member
          • Aug 2016
          • 165
          • germany
          #3
          I've done a lot of Google searching
          there are two either/or options for this IC.
          Attached Files
          Last edited by samtron786; Today, 03:41 AM.

            Comment

            • samtron786
              Senior Member
              • Aug 2016
              • 165
              • germany
              #4
              Before
              After turning on the coffee maker, it immediately rinses, and the water flows into the tray. Then the indicator lights for no water, coffee grounds, and the triangle start flashing simultaneously.
              ich frage mich
              was ist das jetzt U7
              Last edited by samtron786; Today, 04:00 AM.

                Comment

                Previous template Next

                Related Topics

                Collapse
                • Jane
                  How do you test MOSFET in laptops ?
                  by Jane
                  I tried to use this method:

                  Testing an N-channel MOSFET:

                  Step 1: Discharge the Gate (turn off the MOSFET)
                  Place the black probe (COM) on the Source (S) and the red probe on the Drain (D). The multimeter should show no continuity (high resistance or "OL" – open line).
                  Then, touch the black probe to the Source (S) and the red probe to the Gate (G). This discharges any stored charge in the Gate, turning the MOSFET off.

                  Step 2: Charge the Gate (turn on the MOSFET)
                  Now, place the red probe on the Gate (G) and the black probe on the                  ...
                  09-27-2024, 03:31 AM
                • Nooy
                  VGA MOSfet permanently shorted and loss of MOSfet pad
                  by Nooy
                  Hello everyone, I recently found this badcaps site and super Learn Electronics Repair youtube channel. And I wanted to learn how to troubleshoot power supplies and VGA cards and how to practice soldering, since I already have a properly defective piece of them. I am currently trying to solve two problems:

                  I have a Gigabyte GV-RX460WF2OC-4GD type card. I managed to find the faulty MOSfet (AON6414A) on it, which I replaced. The card starts up, but after about half a minute, the MOSfet in the same position will be shorted again. Is it possible that the PWM controller driving the MOSfet...
                  02-14-2024, 02:26 AM
                • AppleLover123
                  Asus X712EA 3 volts after the first mosfet
                  by AppleLover123
                  Hey guys,

                  i have a asus motherboard here and as the title says after the first mosfet (in the picture) there is nothing more than 3.15v.
                  I injected 19v and max. 1 amp at the charging port and there is not voltage drop or smth. It's just taking 19v and 1 milliamp.
                  Then i tried to inject 19v and max 1amp after the current sensor and there it first takes 19v and 4 milliamps and after 2 seconds it is taking nothing (no current).
                  I measured on the coils on board everything seems fine. Also the main power rail is not shorted (infinite resistance).
                  Now i thought something...
                  12-15-2024, 07:49 AM
                • MicroSMD Lab
                  ASUS ROG Zephyrus GPU Mosfet repeat failure
                  by MicroSMD Lab
                  The board number is GU502DU. I repaired this a couple weeks ago and it came back with the same issue, same mosfet failed (PQH9201). I'm hoping that the GPU was spared this time.
                  I used the same replacement part (purchased from Mouser) and I'm certain the soldering was done properly since it took just as much effort to remove as before. What could cause this same mosfet to fail? I'm thinking if it was unsuitable then the others would fail too. I looked for similar failures on YTube and the mosfet was replaced with AOE6930 in one instance and AOE6932 in the other but it's possible that the...
                  01-10-2024, 06:36 AM
                • Scotchmist
                  Asus GA502D keeps blowing mosfet
                  by Scotchmist
                  I have an Asus GA502D, it had a blown mosfet which I replaced and the laptop booted into windows, a few mins later it shut off, the same mosfet was blown. I thought maybe just a bad mosfet but same thing happened again, a few mins in windows and shuts off.

                  I have removed the mosfet and can run the laptop no problem

                  The MOSFET is FDPC5018SG

                  Can anyone point me in the direction of what could be the cause of this, could it be the controller rt3663bc?

                  Thanks
                  08-24-2024, 02:23 PM
                • Loading...
                • No more items.
                Working...