A magnetron can test good, but yet be bad. Rare, but can happen.
-
-
Hi.
I just received the magnetron today!
Bosch Spain is a disgrace! They sent me a Chinese magnetron from Aliexpress for 26 euros!
https://es.aliexpress.com/item/32965...tml?src=google
But I paid 136€ for original!
The differences are visible. The cap is different.
But the microwave started and works.
It means that error E1006 is a magnetron malfunction.
and E1003 loss of feedback from the inverter board.
Thank you everyone who helped me.
Comment
-
Good to know my gut feeling was correct. I am very disappointed to hear that you ordered an original magnetron but instead got an cheap @$$ AliExpress copy.
But at least the microwave works. Good going!
Since you got a new magnetron and everything works, maybe take the old magnetron apart.Comment
-
just had the pleasure of looking at a broken microwave . blown fuse so bridged it for fun . turned it on and loud hum then transformer smoked . i got 2 handy magnets from the magnetron the rest is scrap .Comment
-
Hi all!
HISENSE 65E7KQ PRO
RSAG7.820.13512 - chassis
MT9618BAATAB - cpu
RSAG7.820.12059 - power
HD650Y3U77 - panel
KLM8G1GETF - emmc
The TV does not turn on, the standby indicator is on. All voltages are present.
Emms is dead. Not readable, not detected.
Replaced emmc.
But with another dump there is no launch
Terminal log
UART
<
AC_ON
RPMB key is not yet programmed
HASH1_VERSION=0x00000000 64bit
E-B
FDE enabled
layout pattern onebin by SAR7,0... -
one of our new (only 4 year old) 1KVA APC UPS stop working and through error P13 contact customer support.
the equipment is out of warranty , upon investigation, we found the inverter board has the fault on the output hybrid relay circuit.
The inverter output relay is parallel by SCR/Triac to enhance the relay performance or other means.
We replaced the SCR with new device,, but the device is not power on as expected.
Further research on the issue found that, the error P13 (event ID 107) is latched on the UPS nvram/MCU and need to clear/reset using a service procedure....09-26-2025, 09:00 AM -
Neff C67M70N0GB-09. After a power grid failure, when the operator turned the power back on, there was some overload, because the oven shows error E300 and nothing can be done, even the clock cannot be set. From what I knew, the operating module (the one with LCD displays) was damaged. Can anyone advise how to fix this? A new module is very expensive, so I would rather repair the one I have. Thanks in advance for your advice .... -
Hello Sharp TV experts
Our Sharp LC-80LE642U displays one short one long flash error code which is a backlight error. I went into service mode and there were 8 lamp error counts recorded. I reset the count to 0 and did a reset. The last monitor error cause was 16 B00014639:12. 16 is the code for backlight error. I tried to power the tv up but went back into error mode.
> I checked voltages on the power supply board and they all check out .. including 3.28 volts at the error pin.
> There is power to the cpu and T-CONN and no faults found there. The cpu has a flashing...01-24-2025, 11:51 PM -
Hi everyone.
I have a HP Elitebook 850 G8.
Serial: 5CG2324XM0
ProdID 6L8D5EC#ABA
It has a Winbond W25Q256JVEN Chip.
I need to remove BIOS Password.
I made a dump with an CHA341A programmer and NeoProgrammer 2.2.0.10.
Attached my dump.
I also used the HP Unlocker tool to create an unlocked file (I followed the guidelines)
I also downloaded latest HP BIOS Update (SP158137) which includes 3 .bin files. I found the Number T76 in my original dump, so I used: T76_01210000.bin
What I did:...
Comment