mariukonie
Member
Last Activity: 10-18-2025, 12:37 PM
Joined: 08-23-2023
Location: London
-
So i replaced everything that looked bad to me and got the board tested but the voltages I get on the secondary are 12 volts, just wanted to ask if this is correct? I thought it should be 18v.... -
I've recently updated bios from r0180z9 and this is folder I found online and used, it supposed to be unlocked but I can't change clock speeds.
Model model vpceh2h1e but on the back sticker it's different vpceh2p0e. s/n 275443535003760
I hope this is what you meant:...Leave a comment:
-
i7 2860QM how to raise power limit?
Hi.
I've just upgraded from i5 2340m TDM 35W to i7 2860QM TDM 45W. All is working fine except during stress test the clock multiplier stays capped at x28 which is 2.8MHz and power draw stays around 35W so it seems the motherboard is limiting power draw. On various websites it reads it should go to 3.3MHz on all 8 cores stressed.
What is the best way to go about raising power limit.
a) Bios upgrade/unlock?
b) Hardware/shunt mod?
c) Reduce the CPUs voltage somehow?
Sony Vaio VPCEH2H1E
BIOS Insyde Version R0200Z9 date 19/04/2012
Can anyone help with... -
Thanks. I'll look for something more powerful....Leave a comment:
-
Thank you. Do you think I can use BC817 and BC807 because they are easier to get hold of?Leave a comment:
-
Hello. I hope you're well. I need to identify 2 elements near the IGBT in the SOT-23 package marked 1M and B97 (Q33S and Q23S).
Fragment of the hob from the Vestel 20FR25 induction cooker with IGBT 20N135SRA.
Internet search results are inconclusive. Thanks for your help.
​...Leave a comment:
-
I've noticed TPM 2.0 is also required for Win11. What do you think will Win11 work on my laptop?Leave a comment:
-
SONY VAIO PCG-711911M VPCEH2H1E advice about updating BIOS to UEFI needed please!
SONY VAIO PCG-711911M VPCEH2H1E
Hi. I can't upgrade to win11 I think it's because my BIOS is without Secure Boot function. The BIOS version is R0180Z9. Can you please advise if it is possible to upgrade BIOS to UEFI for this laptop. Many thanks.... -
Thanks. E300 on mine is static, I did put it into test mode as shown in video and it was testing everything fine but there are some settings that I don't know what they mean, Should I just try different settings on a hit and miss basis?
Pressing clock button and unplugging for 10 seconds also didn';t help....Leave a comment:
-
I know my soldering is bad, I'm working on it
I don't have sny schematics unfortunately but the orange cables are the ones that come in from main control pcb so they are supplying module with power hence I would guess that's where surge of power would come in What would be the most likely culprit? All black cables go to control knobs on the front panel....
Leave a comment:
-
Thanks. Please ignore some bad looking solder​s as I was already trying to diagnose it a little bit. ...
Leave a comment:
-
Neff C67M70N0GB-09 fault code error E300 - How to fix it?
Neff C67M70N0GB-09. After a power grid failure, when the operator turned the power back on, there was some overload, because the oven shows error E300 and nothing can be done, even the clock cannot be set. From what I knew, the operating module (the one with LCD displays) was damaged. Can anyone advise how to fix this? A new module is very expensive, so I would rather repair the one I have. Thanks in advance for your advice .... -
Thank you Boss. Best regards....Leave a comment:
-
Hi again. Thanks for all help. I've managed to find the problem, it was the motor and motor controller STK5Q4U363J on module .
I got two STK5Q4U363J from Aliexpress, First one didn't work fortunately second is OK
I got second hand motor from ebay.
After replacing these the washer dryer works perfectly.
Regards....Leave a comment:
-
Thank you so much. This is very useful. I couldn't find it myself. I'll do the procedure and post results.
I got my hands on repair instructions of very similar model I'll go ahead and do all checks recommended and post update very soon.
Thanks for help much appreciated....Leave a comment:
-
I don't know how to get it into test mode, can't find any info online, How is it done please?
I tried unplugging heater, still the same.
Tried cycling through fault codes, nothing. Just one code E:60 -09
Just read that these suffer from dryer becoming unsealed and I remember there was lot of moisture on the inside when I took cover off, I just thought it was because it was in garage but it was quite a lot of moisture. It was more than week ago so it's all well dry now....Leave a comment:
-
I always had appliance plugged in through RCD. If there was leakage it would trip RCD.
I did test resistance between body and heater terminals and it's OL, I know it's different under voltage but RCD would notice it.
Resistance between heater element terminals is in normal range.
I'm thinking if heater was faulty it should have still do spin cycle.
It does go into dry cycle and heats up but not turning drum
Does anyone have repair instructions for this Model Number WDU28560GB/02
That would really help to test everything and eliminate other possibilities. ...Last edited by mariukonie; 12-05-2023, 08:30 AM.Leave a comment:
-
Thanks. I've tested the heater element. It seems okay. Is there any was to reset and erase the codes?Leave a comment:
-
Bosch WDU28560GB/02 washer-dryer - time jumps, blocked door, codes E60 and -09
Bosch WDU28560GB/02 washer-dryer. After selecting the spin program, the clock jumps from 0:13 immediately to 0:05 and counts down the minutes to zero. The pump turns on and the door locks, but nothing else happens, the drum doesn't spin. After the countdown ends, it does not open the door, it can only be opened by pulling the emergency handle next to the filter. No error is shown. When I select spinning and hold my finger in the lower left corner of the screen, after 5 seconds E60 and -09 are shown alternately. What could be the problem? Is it possible to turn on the service mode so that the washer-dryer...
No activity results to display
Leave a comment: