cant quite read it as hole blown through ...
is this a NCP1014AP065G ?
Collapse
X
-
Tags: None
-
Re: is this a NCP1014AP065G ?
from the datasheet - yes.
all variants are AP,
ending values are 06, 10 or 13.
clearly this is 06.Attached Filesif you find these attachements useful please consider making a small donation to the site
-
Re: is this a NCP1014AP065G ?
nice one . just needed confirmation ... its from my tv power supply . main capacitor open circuit . suppose thats what killed it ? quick check of diodes etc nothing else appears shorted .Comment
-
Re: is this a NCP1014AP065G ?
Getting a bit o/t, but if your TV PSU has Active PFC (APFC), you might want to make sure that circuit is running as it should be and not overshooting. Main capacitor going open-circuit can be attribute to either bad part (crap cap brand) or APFC overshooting and killing the cap over time. Usually it's #1, but I've seen the latter wreck even good quality brands too. Something to keep in mind after replacing the main capacitor and that NCP1014 chip.Comment
-
Re: is this a NCP1014AP065G ?
there are 2 bulged caps on the board i am replacing as well .
bit of history .tv always worked well but would sometimes forget what source was selected when coming out of standby .. i had been away a week and on my return i plugged the tv back in and no standby . grabbed the hair dryer and warmed it up .stand by light come on and switched on fine .left it on and ok for first night . next night it was off when i woke up . no standby light . so far found this ic blown up . 2 bulged 4700uf 6.3v caps and main 150uf 450v cap open . plus a blackened open fuse .
open cap is a capxonLast edited by petehall347; 09-28-2018, 04:27 AM.Comment
-
Re: is this a NCP1014AP065G ?
well its up and running . replaced 4 caps in all plus the ic . tv starts up in 4 seconds .
main filter cap replaced with 150uF 450v SNAP-IN, Rubycon (JAPAN) HXG 105C, ripple:1.51A! LIFE 3000HrsComment
-
Re: is this a NCP1014AP065G ?
sorry its back together .. tv is an odd one locally built . evesham computers was one of their company names . think they are out of business now . hold on might have got a pic will check the phone .
edit ..sorry only a pic of chip . i did have a tab open with same one but long closed it . will see if in historyLast edited by petehall347; 10-07-2018, 05:35 PM.Comment
-
Related Topics
Collapse
-
by silberdracheHello,
I'm new to this Forum, so I hope it's the right place for this topic.
Im a student from germany, and as a hobby I repair electronics. I started microsoldering maybe 1-2 years ago.
I have a MacBook Pro 14" m1 Pro with 10 Cores and 16/1tb storage. The board Number is 820-02098-A.
The MacBook has a light water damage. Coffee got spilled over it, but the Mac continued working only the battery didn't charge anymore and when the battery was empty the Mac turned off and doesn't show any sign of life now.
I opened it up and there were only three drops of coffee... -
by cmlewis89Hi folks,
I'm new to this forum. So my trusty 17-year-old LG 47" LCD recently died. As I was booting it up, I heard a hum followed by a loud bang, sounds of pieces flying around, and loss of power to the unit. Inspecting the PSU, I saw two obvious problems: a blown thermistor (bang + flung pieces) and a visibly bulging main cap. Inspecting as many components as I could with my Fluke MM, I diagnosed that the following components on the "hot side" of the board were also bad: one of the 2 main MOSFETs, main 8A fuse, small cap (25V 47uF) connected to main caps, and a blown...12 Photos -
by drscootHP Modelnumber: 14-dh0061nb
This laptop had a shorted cap on a Vcore section. After replacement is works again. But there is still a battery issue.
The battery is HT03XL and with the built-in component test from HP, in the Power section, I get an error: Logic State: Calibration required (20), Charge state: Blown Fuse (42)
I have another same battery, also with error: Logic State: Very Weak (70), Charge state: Blown Fuse (42)
And a third battery TF03XL (looks identical) with error: Logic State: OK (0), Charge state: Blown Fuse (42)
All these 3 batteries are charging...2 Photos -
by w00pzI have blown a component on HP Envy x360 with motherboard G1 13 AMD X360 18740-1 448.0GA03.0011.
Unfortunately there are no schematics available and the component was so blown the marking weren't readable.
I have marked it with a red circle in the attached photos - sorry for the mediocre quality I was too much in a rush.
Hope someone will be able to identify the component.
Many thanks for your help!
Edit: High-res picture added on a normal board (not mine)...2 Photos -
by swergHey everyone,
I'm a novice trying to repair my laptop. The LCD screen has an image, but no LED backlight for the image. It also produces an image when connected to an external monitor.
I have found what I believe to be a blown inductor labeled "L4502" and "120 Ohm" in the schematics (zoomed in image, blue arrow to blown component). I have included an image of the general area of the mobo and an excerpt from the schematics as well.
I am having trouble selecting a replacement component, which I believe to be a 120 Ohm ferrite bead, from the components... - Loading...
- No more items.
Comment