Announcement

Collapse
No announcement yet.

Interesting stuff - truck air conditioner unit board

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Interesting stuff - truck air conditioner unit board

    Got PCB from brothers truck air conditioner unit. It seems to be Waeco CA-800. So far I have discovered it is 24V powered unit, obviously with step-up transformer - transforming most likely to 230 V for compressor and maybe also the fans (at least two fans in there).

    From what I know, board is defective for most people with this unit and it is supposedly worth of at least 400 USD/300 Eur, so you can see there is some point in repairing this thing

    In this case it is supposedly dead, connecting it directly to 24 V resulted in burning two fuses. I have nothing but camera with me here (at home now) so I will clean it and take some pictures for you guys, than I will check all the diodes/rectifiers and transistors when I will be back to my "lab"

    Stay tuned!
    Less jewellery, more gold into electrotech industry! Half of the computer problems is caused by bad contacts

    Exclusive caps, meters and more!
    Hardware Insights - power supply reviews and more!

    #2
    Re: Interesting stuff - truck air conditioner unit board

    Man its covered with some stuff, it seems like dust with some pitch-like thing most likely from other cars and trucks exhalations. I cleaned some after half an hour of fun with technical gas, but still…
    Attached Files
    Less jewellery, more gold into electrotech industry! Half of the computer problems is caused by bad contacts

    Exclusive caps, meters and more!
    Hardware Insights - power supply reviews and more!

    Comment


      #3
      Re: Interesting stuff - truck air conditioner unit board

      It looks like it uses permanent magnet 3-phase motor drive system (you can see 3 pair of MOSFETs on one side of the heat sink) for the compressor, transformer is too small to be stepped up to 230V, this unit consumes 800 Watts of power. So far cannot find diagram yet.
      Never stop learning
      Basic LCD TV and Monitor troubleshooting guides.
      http://www.badcaps.net/forum/showthr...956#post305956

      Voltage Regulator (LDO) testing:
      http://www.badcaps.net/forum/showthr...999#post300999

      Inverter testing using old CFL:
      http://www.badcaps.net/forum/showthr...er+testing+cfl

      Tear down pictures : Hit the ">" Show Albums and stories" on the left side
      http://s807.photobucket.com/user/budm/library/

      TV Factory reset codes listing:
      http://www.badcaps.net/forum/showthread.php?t=24809

      Comment


        #4
        Re: Interesting stuff - truck air conditioner unit board

        Didn't find much too, not even any information on spare parts (fans or compressors), but the one big capacitor on secondary side is for 400 V which would suggest 230 V. Input is 35 V/4700 uF, thats OK for 24 V, we are in car, the voltage fluctuates really.

        (I know that while lead/sulfur acid battery is labeled 12 V, when fully charged its voltage is as high as 12,8 V, which means 25,6 V here. But for charging you actually use some 14,5 V (so this must go from generator, right?) so it is some 29 V here. You cant run such bloody thing from the battery;-) Not more than for 5 minutes.)
        Less jewellery, more gold into electrotech industry! Half of the computer problems is caused by bad contacts

        Exclusive caps, meters and more!
        Hardware Insights - power supply reviews and more!

        Comment


          #5
          Re: Interesting stuff - truck air conditioner unit board

          That was the first thing I searched for, replacement compressor. The unit is advertised as a 24V compressor system, Operating range is 20~30VDC, 12~22A.

          Must be made for big truck that runs on 24V system.
          Never stop learning
          Basic LCD TV and Monitor troubleshooting guides.
          http://www.badcaps.net/forum/showthr...956#post305956

          Voltage Regulator (LDO) testing:
          http://www.badcaps.net/forum/showthr...999#post300999

          Inverter testing using old CFL:
          http://www.badcaps.net/forum/showthr...er+testing+cfl

          Tear down pictures : Hit the ">" Show Albums and stories" on the left side
          http://s807.photobucket.com/user/budm/library/

          TV Factory reset codes listing:
          http://www.badcaps.net/forum/showthread.php?t=24809

          Comment


            #6
            Re: Interesting stuff - truck air conditioner unit board

            Yep, it is from unit in truck brother which operates. However, as I said, due to the price and the fact ALL trucks in the company have the unit inoperational, they don't want to replace it. And brother won't buy board into somebody elses truck, right? So if I can repair it for fraction of its price;-)

            It operates on 24 V, yes, but from diagrams, the compressor seems like ordinary compressor you find in fridge! And I see no point in running this thing on low voltage - insane looses with currents in 10 A range. Together with the fact there is high-voltage cap on secondary, I think it is really step-up for ~230 V, at least for the compressor, fans could operate on either 12 or 24 V.
            Last edited by Behemot; 06-22-2012, 02:29 PM.
            Less jewellery, more gold into electrotech industry! Half of the computer problems is caused by bad contacts

            Exclusive caps, meters and more!
            Hardware Insights - power supply reviews and more!

            Comment


              #7
              Re: Interesting stuff - truck air conditioner unit board

              If you can get to look at how many wires are from the compressor then it may help identifying the type of motor is used for the compressor, it also should have tag on the compressor itself. 24V single phase is not efficiency, multi-phase DC is more efficiency and they can electronically control the speed with the amount of load requirement so it will not put heavy drain on the truck power system.
              If you can fix one, more likely the other will have the same failure mode, then your brother cam save a lot of money and you may be able to offer repair service to other truck owners as well. Troubleshooting the first one will be difficult, but once you figure it out, then it will be easy from then on.
              Never stop learning
              Basic LCD TV and Monitor troubleshooting guides.
              http://www.badcaps.net/forum/showthr...956#post305956

              Voltage Regulator (LDO) testing:
              http://www.badcaps.net/forum/showthr...999#post300999

              Inverter testing using old CFL:
              http://www.badcaps.net/forum/showthr...er+testing+cfl

              Tear down pictures : Hit the ">" Show Albums and stories" on the left side
              http://s807.photobucket.com/user/budm/library/

              TV Factory reset codes listing:
              http://www.badcaps.net/forum/showthread.php?t=24809

              Comment


                #8
                Re: Interesting stuff - truck air conditioner unit board

                Yep, I know, thats the second thing Well, from what he told me, different company had similar problem, many boards were damaged, one heavily coroded, one even broken in half, only one unit beyond repair. I can get contact to one guy who did it in this second firm, but the gus is supposedly "busy and stuff", you know how it works

                I can only try to access brothers truck which he has on parking lot during weekend, than nothing. I asked him for that too, first thought I may find some info on web, but obviously there is nothing and I will have to look at that
                Less jewellery, more gold into electrotech industry! Half of the computer problems is caused by bad contacts

                Exclusive caps, meters and more!
                Hardware Insights - power supply reviews and more!

                Comment


                  #9
                  Re: Interesting stuff - truck air conditioner unit board

                  Looks like a 2-sided board with nice big traces, so it shouldn't be hard at all to trace it and derive a schematic, then figure out how it's supposed to work.

                  Post clear directly-overhead pictures of the front and back if you'd like some help

                  Comment


                    #10
                    Re: Interesting stuff - truck air conditioner unit board

                    Sure, in my lab, I have also some photo stuff there, including good light and white surface
                    Less jewellery, more gold into electrotech industry! Half of the computer problems is caused by bad contacts

                    Exclusive caps, meters and more!
                    Hardware Insights - power supply reviews and more!

                    Comment


                      #11
                      Re: Interesting stuff - truck air conditioner unit board

                      Might check the board for cold solder joints?? I have seen this in several boards on Honda and GM products.

                      Comment


                        #12
                        Re: Interesting stuff - truck air conditioner unit board

                        OK, finally got to it. What I found so far is one shorted transistor - IRF1010N - on the input side. That would explain the blown fuse.

                        IRF3205 seems to be more than good substitue. Only thing I do not know is the fuse I should use. I can simulate 24 V with two lead UPS batteries, hopefully if it would work without the panel I will see what voltages come from it. I think I can be safe with regular 6,3A fuse for the time being, since there is no output really it should not consume much power.

                        ADD// as for the topology side, output is definitelly high-voltage, than it goes to the collector (most likely, but central pin :-)) of single transistor in every of the three couples. Every couple is driven by IR2104 half-bridge driver. My guess is it is there to simulate sine-wave, whaddaya think?
                        Last edited by Behemot; 08-15-2012, 01:36 AM.
                        Less jewellery, more gold into electrotech industry! Half of the computer problems is caused by bad contacts

                        Exclusive caps, meters and more!
                        Hardware Insights - power supply reviews and more!

                        Comment


                          #13
                          Re: Interesting stuff - truck air conditioner unit board

                          Originally posted by Behemot View Post
                          OK, finally got to it. What I found so far is one shorted transistor - IRF1010N - on the input side. That would explain the blown fuse.

                          IRF3205 seems to be more than good substitue. Only thing I do not know is the fuse I should use. I can simulate 24 V with two lead UPS batteries, hopefully if it would work without the panel I will see what voltages come from it. I think I can be safe with regular 6,3A fuse for the time being, since there is no output really it should not consume much power.

                          ADD// as for the topology side, output is definitelly high-voltage, than it goes to the collector (most likely, but central pin :-)) of single transistor in every of the three couples. Every couple is driven by IR2104 half-bridge driver. My guess is it is there to simulate sine-wave, whaddaya think?
                          I say you should give it a go
                          Muh-soggy-knee

                          Comment


                            #14
                            Re: Interesting stuff - truck air conditioner unit board

                            Brother informed me there used to be a 30A fuse, so I bought some for testing :-D (this stuff is pretty cheap compared to for example glass fuses!) Also got the transistors so I can give it a try, yes. Gonna have a nap for it and play with that during night after some sleep, just for case
                            Less jewellery, more gold into electrotech industry! Half of the computer problems is caused by bad contacts

                            Exclusive caps, meters and more!
                            Hardware Insights - power supply reviews and more!

                            Comment


                              #15
                              Re: Interesting stuff - truck air conditioner unit board

                              OK, got some nice sparks and one dead 30A fuse Not sure what to do next, nothing seems to be wrong in there from my point of view. The problem should be on the primary side as being on secondary, it would just blow things there. But all the IRG4BC20KDs (IGBT) are fine.

                              Well, there is also one slightly burned component which seems to be SMD resistor. It actually looked good before I touched it, than the top layer with printings just dropped of I remember there was something like 162, maybe 1R2 or 1k2? It reads some 1130 ohms…it is between the two primary transistor gates like: gate-SMD cap-resistor-gate
                              Last edited by Behemot; 08-16-2012, 01:26 AM.
                              Less jewellery, more gold into electrotech industry! Half of the computer problems is caused by bad contacts

                              Exclusive caps, meters and more!
                              Hardware Insights - power supply reviews and more!

                              Comment


                                #16
                                Re: Interesting stuff - truck air conditioner unit board

                                Originally posted by Behemot View Post
                                OK, got some nice sparks and one dead 30A fuse Not sure what to do next, nothing seems to be wrong in there from my point of view. The problem should be on the primary side as being on secondary, it would just blow things there. But all the IRG4BC20KDs (IGBT) are fine.

                                Well, there is also one slightly burned component which seems to be SMD resistor. It actually looked good before I touched it, than the top layer with printings just dropped of I remember there was something like 162, maybe 1R2 or 1k2? It reads some 1130 ohms…it is between the two primary transistor gates like: gate-SMD cap-resistor-gate
                                Probably a mosfet driver chip has gone bad also.
                                Muh-soggy-knee

                                Comment


                                  #17
                                  Re: Interesting stuff - truck air conditioner unit board

                                  There are two, TL494 and "258 EZ621" from ST Micro. Actually, there are some paths going all the way arround the rim to the part with more SMD components. There are two more EZ261 and lots of other stuff.

                                  The thing is, if something from this would be shorted, do you think it can blow of 30A fuse without melting the paths? :P I think it is something more major, but can't find it though…
                                  Less jewellery, more gold into electrotech industry! Half of the computer problems is caused by bad contacts

                                  Exclusive caps, meters and more!
                                  Hardware Insights - power supply reviews and more!

                                  Comment


                                    #18
                                    Re: Interesting stuff - truck air conditioner unit board

                                    Originally posted by Behemot View Post
                                    There are two, TL494 and "258 EZ621" from ST Micro. Actually, there are some paths going all the way arround the rim to the part with more SMD components. There are two more EZ261 and lots of other stuff.

                                    The thing is, if something from this would be shorted, do you think it can blow of 30A fuse without melting the paths? :P I think it is something more major, but can't find it though…
                                    If you were to apply 30A for a long time, the traces would begin to melt and smoke.

                                    But, they can handle a surge current to some degree.

                                    Take all the mosfets out and see if it still blows the fuse.

                                    If it doesn't, with the mosfets still out, check the gate connections on the circuitboard for shorts to +V and/or ground.
                                    Muh-soggy-knee

                                    Comment


                                      #19
                                      Re: Interesting stuff - truck air conditioner unit board

                                      Can do it, yeah. Will try first with the TO-92 and than proceed with others if it will continue to blow (there are some SMD transistors for DC-DC, low voltage for fans and controll boards I think).

                                      Well, just that after replacing the one transistor, there are no shorts any longer even with having them in, so I thought there won't be any with transistors mounted

                                      Just about the smoke and melting…you know what lead batteries can do, you can solder with them I bet the spike was much greater than just 30 A
                                      Last edited by Behemot; 08-16-2012, 12:12 PM.
                                      Less jewellery, more gold into electrotech industry! Half of the computer problems is caused by bad contacts

                                      Exclusive caps, meters and more!
                                      Hardware Insights - power supply reviews and more!

                                      Comment


                                        #20
                                        Re: Interesting stuff - truck air conditioner unit board

                                        OK, it is still blowing fuse after unsoldering primary transistors.

                                        But here is the deal. I have been thin king about the diode (the huge one) which is on input side, just after fuse. Can it really work with diode being in conducting state between voltage and ground? Shouldn't the diode be, like a, in opposite state to block half of the AC when it would accidentally be applied?

                                        It should, right? So, how big idiot am I to solder it in like that? Tell me please…
                                        Last edited by Behemot; 08-20-2012, 03:27 PM.
                                        Less jewellery, more gold into electrotech industry! Half of the computer problems is caused by bad contacts

                                        Exclusive caps, meters and more!
                                        Hardware Insights - power supply reviews and more!

                                        Comment

                                        Working...
                                        X