can find an rh spec sheet! but not the LL one, i hate when ya call a component store, get only so much info! he could not tel me if low esr or really anything. so what are they?
-
-
Re: mcrh16v477m10x13-ll
1) I think this is the wrong section, maybe.
Don't see a LL series listed.
http://uk.farnell.com/jsp/search/pro...uteId%3D100000
What kind of cap is it?
Got a picture?Last edited by cmj21973; 03-09-2012, 04:04 PM. -
Re: mcrh16v477m10x13-ll
no pic! called a store a couple hours away from me to get replacement for a capxon 470uf 16v 105c gf, out of a viewsonic lcd. said all they had was " multicorp" caps! so got part number, an asked what markings were on cap! 470uf 16v 105c LL . an had an m on it! not with circle round it so not a panasonic! could not find LL for any series of cap! but answer is in me thread title i think, it an rh.,. mc"multicorp" rh"series"
thanx for your time!
peace
sorry bout wrong section!Last edited by t.j.; 03-09-2012, 11:25 PM.Comment
-
Recapping the power supply board for a Samsung 305T monitor, everything is Capxon except 2 Rubycons. I can't find data sheets matching these online, so don't know what ripple numbers, impedence, etc, to look for. There are a few different looking GL series data sheet PDFs, but the listing that matches the capacitance and voltage is a much bigger case size. I've narrowed down selections with lead spacing and case diameter, and what's in stock at Digi-key
1 x Capxon 1000uf35v GL C720(is this a part number or batch number, can't find it anywhere) 105c
1 x Capxon 1000uf35v... -
In my search for a proper 5v heavy ATX power supply, I selected an old Antec SU-380 that I've had in storage for a long time. Opening the power supply reveals a couple bulged capacitors. I removed all the caps and made a map for myself. I found the datasheet for the PCE TUR series in this thread:
https://www.badcaps.net/forum/showthread.php?t=14159
It says these are general purpose, so I assume I can replace them with any general purpose capacitors, but I don't really know anything about power supply circuits or reading capacitor datasheets. Despite this, I've been shopping for replacements:... -
Hello all, new member here. I replaced the LED strips and found that the BL can be turned on with the TCON board and LCD panel disconnected. So new LED strips are working fine. Now the problem. There are 3 diffuser sheets on this set. One sheet is thicker than the others and I know it goes in first next to the LED strips. But one side of this sheet has a rougher texture than the other side. Does the rough side go up or down? The 2 thinner sheets have tabs that will only allow them to be installed one way so that's good. One sheet is what I would call plain translucent. The other sheet is whiter... -
So I had to replace the LED lights on this TV and that worked out nicely. But the White reflector sheet that helps to diffuse the led lights evenly was glued into the back chassis which had to be removed to replace the LEDs.
Placing the white reflector sheet caused it to not sit evenly - causing weird diffusing when TV was all put together. Picture is still decent, but now there are dark and light spots due to the white reflector sheet not sitting against the back chassis.
Anyone have thoughts on replacement white reflector? or do I just scavenge broken TVs for... -
Hello everyone,
I'm working on repairing a Music Store Professional GO! SUB 18A bass subwoofer, and I need some help troubleshooting an issue with the power amplifier board. The board uses an IR2153 driver and originally had two SLW20N50C MOSFETs. Unfortunately, these MOSFETs burned out. I replaced them with two TK20J60W MOSFETs; however, these also failed almost immediately.
Here are some details:- SLW20N50C (original):
- Rated for 500 V
- Typical RDS(ON): 0.21 Ω
- Continuous Drain Current: 20 A at 25°C (13 A at 100°C)
- Pulsed Drain Current: 80 A
- Avalanche
- SLW20N50C (original):
Comment