Help! Recapping Gone Bad...

Collapse
X
Collapse
 
  • Page of 2
  • Time
  • Show
Clear All
new posts
Previous 1 2 template Next
  • PCBONEZ
    Grumpy Old Fart
    • Aug 2005
    • 10661
    • USA
    #21
    Re: Help! Recapping Gone Bad...

    Originally posted by MXM
    like from the base, were the handle ends and the iron starts. i guess the plastic couldnt handle it haha... i said it broke cause you know i was using it, and out of the sudden at the middle of soldering..... it split in two the only bad was the small burnt i got, but nothing for the ER

    mi internet is being a bitch took me 3 hours to upload the pics for my other thread on this board today... but lemme give it a new try on this.

    https://www.badcaps.net/forum/attach...id=16889&stc=1

    k it worked


    on the other hand... can anyone please give me some advise, the board in mention has a thread with all the info of what ive done to it, pics and stuff, anything is welcome.

    https://www.badcaps.net/forum/showthread.php?t=10266

    thanks
    There are supposed to be screws that hold the element tube to the handle.
    Were they missing?

    .
    Mann-Made Global Warming.
    - We should be more concerned about the Intellectual Climate.
    -
    Be who you are and say what you feel, because those who mind don't matter and those who matter don't mind.
    - Dr Seuss
    -
    You can teach a man to fish and feed him for life, but if he can't handle sushi you must also teach him to cook.
    -

      Comment

      • kaniki
        Badcaps Veteran
        • Dec 2009
        • 514
        #22
        Re: Help! Recapping Gone Bad...

        screws??? what are you thinking.. it should have a decent amount of duct tape and super glue.. who needs screws???

          Comment

          Previous 1 2 template Next

          Related Topics

          Collapse
          • corrize
            Best way to solder LVDS connector for beginner (and qfn) ?
            by corrize
            Hello, I'm a beginner for micro soldering. Right now I have some difficult to solder a qfn 20, I guess I put too much solder on the thermal-ground pad, the result is a corner of chip wich don't touch the board (last try).

            I use a wire solder with hot air, I tin the board and chip before with iron and I use good flux.

            I will have to solder a LVDS connector (40 pins, laptop pc), I saw a solder paste in seringe, good quality (it does not scatter).
            See the test :
            https://youtu.be/bNAzC-EvqHs?t=1767

            With hot air from bellow the board, that's...
            03-09-2023, 02:57 AM
          • petemanuk
            BGA solder balls not connecting - help pls
            by petemanuk
            So I though in my spare time I’d set myself up repairing motherboards mainly pin damaged lga1151 sockets types.

            I’m using an achi ir sc pro rework station (gave up on my Achie ir6500 - don’t recommend)

            I’ve managed to get my rework profile somewhere in the correct region (after a lot of trial and error) to get the old sockets off and reflow new ones back on again, the problems I’m getting is not all of the solder balls are re-attaching when re-flow occurs. I know this because when socket is removed pads still look clean and have no solder...
            11-16-2022, 05:21 AM
          • myth77
            UV solder mask - high temp resistent, recomendation?
            by myth77
            Can someone recommend any good UV solder mask? But i need a solder mask that will stand high temperetures. The thing is...sometimes i have a bigger cooper ripped from the board, lets say mosfet pad... i reconstract it with cooper sheet, then i "glue it" with solder mask...then i use UV light...and let it cool a bit. After, i try to clean the cooper of extra solder mask..and till that part all is ok. But, when i use a soldering iron to solder that pad/cooper...the solder mask gets weaker or destroyed and finally the pad is ripped again from the board .
            Is there any solder mask...
            03-28-2022, 04:04 AM
          • flibidy
            Magnum IA.100 Amplifier Switches on, No Output, Possible Input Side fault?
            by flibidy
            I have here a Magnum IA.100 which belongs to my parents.



            The unit powers on & when the relay kicks in, you get a pop from the speakers (this might sound weird but is usual behavior for this amp). However, you get nothing coming through it from any of the inputs & no pops and crackls from any of the controls.


            Because of the sound from the speaker when the amp turns on I have assumed that the output section probably works but I could be wrong & I'm not sure how to test that side of things further.


            What Ive done........
            Magnum IA.100 Front
            8 Photos
            01-01-2025, 01:26 PM
          • acedogblast
            Guide to transplant MEC1503 EC chip and EEPROM reprogamming for T14s gen 2 and X13 gen 2
            by acedogblast
            This is a guide that I am writing for helping others to replace their MEC1503 EC chip if it breaks (or to get around an inconvenient prompt to the BIOS). This forum has been extremely helpful to me so I would like to contribute to help others. I will tell you right now that this task is very difficult to do. You MUST have experience and tools to do precision micro-soldering, BGA reballing, trace repair, and general laptop repair skills.

            There are some specialty tools needed to do this task. The replacement MEC1503 chips can be acquired from Aliexpress. Do not buy the bare chips as...
            11-02-2024, 05:13 PM
          • Loading...
          • No more items.
          Working...