Chenming/Antec with CWT

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • 370forlife
    Large Marge
    • Aug 2008
    • 3112
    • United States
    #1

    Chenming/Antec with CWT

    I went to a lan party where this kid had a chenming case identical to the one in the thread in the for sale section. He was still running the included psu, it was a "ISO switching power supply", ul'd to Channel Well Technologies.

    I know antec cases of this era were chenming, don't know if they still are, but their power supplies were also Channel Well Technologies. Coincidence or something else?
    Tags: None
    • PCBONEZ
      Grumpy Old Fart
      • Aug 2005
      • 10661
      • USA
      #2
      Re: Chenming/Antec with CWT

      Not sure.
      CWT builds for LOTS of other companies.
      Mann-Made Global Warming.
      - We should be more concerned about the Intellectual Climate.
      -
      Be who you are and say what you feel, because those who mind don't matter and those who matter don't mind.
      - Dr Seuss
      -
      You can teach a man to fish and feed him for life, but if he can't handle sushi you must also teach him to cook.
      -

        Comment

        Previous template Next

        Related Topics

        Collapse
        • eccerr0r
          old X58 triple channel board... memtest86 memory speed?
          by eccerr0r
          Anyone run memory speed tests with an old X58-based triple channel 1st gen or any other >2 channel board? The one I have is a Gigabyte I think.

          Anyway I had four 4GB DDR3-1333 modules in the 6 memory slots and got around 11GB/sec memory speeds assuming that it went dual channel since it didn't have enough modules for triple channel. Now I stuck in two more 4GB modules, but they are DDR3-1600. I'm still getting 11GB/sec speeds according to memtest86...

          Just wondering, anyone do memory speed analysis on these triple (and higher) channel memory boards? Are there any...
          06-28-2025, 09:06 AM
        • spleenharvester
          Reverse engineering of 18650 4-channel tester
          by spleenharvester
          Hi friends

          I have reverse engineered this tester, schematic is attached and is complete except for capacitor values. These testers annoyingly have no model number but they are the ones you find on the first page of just about any website if you type in "18650 4-channel tester". There is also a 2-channel variant and a newer 8-channel variant. They are very cheap (about £15) and can measure voltage, current, internal resistance and capacity. They have a multicolour display for all these statistics. They also have terminal blocks so that if you want to use a breakout board...
          05-04-2025, 02:43 AM
        • dicky96
          American Audio VLP1500 Distorting on one channel
          by dicky96
          Hi guys I have a VLP1500 amplifier here - one channels works fine and the other channel distorts even at low volume settings

          Protection and Clip LED are off

          There is something wrong with the BIAS voltages around T16 and T18 (in particular) on the bad channel

          I tested all diodes and transistors in this area in circuit with diode mode - both channels seem identical. Same in resistance mode across all the resistors here.

          The output DC voltages on pin1 and pin8 of the 5532D dual op amp at the input of each amplifier module are the same, and the audio...
          07-13-2022, 05:25 AM
        • dicky96
          Hitachi V19B01922 Channel Tune problem
          by dicky96
          Hi Guys
          I have a customer who has two Hitachi TVs in his bar, one is the model in the thread title and the other is a larger screen but has the same setup menu

          He also has an LG TV, so three screens in the bar

          I installed three Satlink ST-6503 DVB-T Modulators
          This model https://www.aliexpress.com/item/32916553905.html

          These connect to three satellite receivers via HDMI cables and then connect to a 4 way RF Amp that connects to the TVs on aerial cable. There is no incoming terrestrial antenna. I set the channel ID on the modulators to...
          02-09-2023, 09:20 AM
        • sima112
          Marantz pm 6005 right channel not worknig
          by sima112
          Hi guys,
          I need a help with my Marantz pm6005. It started to have weaker the right channel a few months ago, than it got back to normal and now it has lost sound completely on the right channel. At the final stage it was loosing the channel for a while and than it returned. After it has disappeared completely I could forced it back by unplugging the source form CD (which I normally use) to phone and back. It would then work for a few minutes and died again. Now it is possible power up and all function works normally (apart the right channel ) on all inputs, except the phone both channel...
          01-30-2023, 12:11 PM
        • Loading...
        • No more items.
        Working...