Running water cooling AIO 24/7/365?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • eccerr0r
    Solder Sloth
    • Nov 2012
    • 8715
    • USA

    #1

    Running water cooling AIO 24/7/365?

    Does anyone here run an AIO or other liquid cooled CPU cooling solution 24/7/365 / on a server? Do you feel comfortable with possible failures? Should I be worried about pump failures? Pump failures causing leaks?

    Having reservations on a second hand cooling system on a PC. So far it's pretty good, keeps things nice and cool but I've never had long term experience with 24/7/365 operation of water cooling, AIO or not. Might have to downgrade to an air cooled system for peace of mind?
  • stj
    Great Sage 齊天大聖
    • Dec 2009
    • 31298
    • Albion

    #2
    they dont leak,
    the failure modes are pump dying and liquid slowly being replaced by air causing air-traps.

    the liquid thing takes several years,
    the pump failure is no different to a fan failure, the pump output's a tacho signal to the motherboard.
    so the system will detect the failure and shutdown.

    Comment

    • eccerr0r
      Solder Sloth
      • Nov 2012
      • 8715
      • USA

      #3
      I'm worried about water boiling and causing vapor gaps, and thus possible thermal damage. I'd imagine a regular heatsink would be far better at dissipating heat long term if the fan died versus pump failure.

      Then there's also the fan on the radiator, and that can fail too. Two possible points of failure?

      Just wondering if I should chance using the liquid cooling system until it dies or preemptively switch to a heatsink/fan combo which will indefinitely dissipate at least some heat... anyone using water cooled systems on a 24/7 server? Trustable?

      BTW I got this computer with the water cooling AIO system and wonder if I should ditch it for a regular hs/f if I wanted to run it 24/7... that's the ultimate issue here versus considering buying a water cooler system... definitely not, IMHO.
      Last edited by eccerr0r; Yesterday, 12:45 PM.

      Comment

      • stj
        Great Sage 齊天大聖
        • Dec 2009
        • 31298
        • Albion

        #4
        i tried / tested unplugging the pump on one,
        the bios shuts the system down real fast if the cpu goes over 70'
        so no worries.
        you arent going to boil the fluid anyway, it's got chemicals like glycol in it and the cpu is not going to go over maybe 60' unless your doing something stupid.

        Comment

        • eccerr0r
          Solder Sloth
          • Nov 2012
          • 8715
          • USA

          #5
          Oh I will be doing something "stupid" ... like compiling things overnight (Gentoo Linux). Also I'd much rather have it throttle than shutdown... perhaps for this constraint, air cooling is better?

          Comment

          • petehall347
            Badcaps Legend
            • Jan 2015
            • 4451
            • United Kingdom

            #6
            will thermosyphon work i wonder ? maybe have it in place as a redundant system ? i dunno

            Comment

            • eccerr0r
              Solder Sloth
              • Nov 2012
              • 8715
              • USA

              #7
              I don't know of any off the shelf cooling systems that are redundant... and all water cooling/AIOs at least, are all waterblock and pump-on-cpu.

              Comment

              Related Topics

              Collapse

              • betmen
                water pump Scala2 - electrical diagram
                by betmen
                Hello,
                Does anyone have a wiring diagram for the pump mentioned?
                The markings on the board are 98800964 r07, two or three capacitors are burnt.
                I don't have the board with me yet, but I don't know if the printed lines on the board are visible due to the short circuit that occurred and how the capacitors were connected.​
                05-22-2025, 02:56 AM
              • Dannyx
                Another water pump automation project (suggestions ?)
                by Dannyx
                Good day folks. Some of you may recall that a while ago I was struggling to put together what I considered to be a very basic automation for a water supply system. It didn't work out the way I intended and I learned my lesson to do it properly from the start, rather than try to reinvent the wheel and patch something together myself from scratch, so I'll stick to commercial alternatives for future projects and such a project just came in today !

                This one is easier simply because this time the pump and level sensors are in the same place, so they don't require a remote connection....
                07-26-2022, 11:39 AM
              • CG2
                Meaco Arete One / Deye Dehumidifier not working
                by CG2
                I've got a dehumidifier that has stopped working. Plug it in, press the power switch, and it beeps 5 times. Nothing showing in the display (which is just two 7 segment displays) apart from the two decimal points flashing. The model is a MeacoDry Arete One 18L, which seems to be a rebadged Deye (all the boards are marked Deye). Here's what I've got so far (details in case anyone else in future should need them).

                Starting with the power board. Mains power comes in at the red connector top left. The compressor is powered by the orange connector to the right of that and is switched by...
                08-17-2024, 07:47 AM
              • mikey5791
                Help repair Panasonic fridge not cooling
                by mikey5791
                Hi all forum members,

                Few days ago, i might have forgotten to close my home fridge freezer door completely. The next day, the ice cubes and frozen meat almost melted halfway and the freezer doesn't feel cool. I shut it off, wipe dry and let it air dry for one whole day. The next day i switched on the fridge, the compressor run for a second and it shuts off(no vibration and no sound at all) only the internal freezer compartment fan is running but is not cooling even i switched on a full day.
                After shut off, i dismantle the rear water pan holder and reached to the compressor wiring....
                07-16-2025, 02:01 AM
              • sam_sam_sam
                Desoldering gun station modified to use a 18 volt @ 20 amp switching power supply
                by sam_sam_sam
                I have wanting to do this project for quite sometime now and I finally found a switching power supply that will work on this desoldering gun station ZD-915 that the original switching power supply took a shit and just was not worth trying to fix it because this switching power is not quite big enough to handle the heater element and the vacuum pump

                One note when I tested the switching power supply and the voltage control board I noticed that this desoldering gun heat up much faster than the original switching power supply which I was really surprised by to the point that I might buy...
                03-31-2024, 02:12 PM
              • Loading...
              • No more items.
              Working...