A 400v 560uf cap today anyone got any good ideas of what i can do with it i am think of a wind up flash light or something along those like that.
Attached Files
-
My Computer.
AMD APU A4-3300 2.5ghz 1mb cache
Motherboard GigaByte GA-A75M-S2V
Kingston HyperX Blue DDR3 8GB (2x4GB)
SB Audigy 2 ZS [B800] Sound Card
500GB WD Caviar® Blue™
1 Terabyte WD Caviar® Black™
2 Terabyte WD Caviar® Black™ -
Re: Received by error
For a flashlight I'd prefer a low voltage high capacitance unit, these high voltage low capacitance units you'd have to use for something like xenon flash or something. -
Re: Received by error
Save it for when you need to replace a PFC CapI love putting bad caps and flat batteries in fire and watching them explode!!
No wonder it doesn't work! You installed the jumper wires backwards
Main PC: Core i7 3770K 3.5GHz, Gigabyte GA-Z77M-D3H-MVP, 8GB Kingston HyperX DDR3 1600, 240GB Intel 335 Series SSD, 750GB WD HDD, Sony Optiarc DVD RW, Palit nVidia GTX660 Ti, CoolerMaster N200 Case, Delta DPS-600MB 600W PSU, Hauppauge TV Tuner, Windows 7 Home Premium
Office PC: HP ProLiant ML150 G3, 2x Xeon E5335 2GHz, 4GB DDR2 RAM, 120GB Intel 530 SSD, 2x 250GB HDD, 2x 450GB 15K SAS HDD in RAID 1, 1x 2TB HDD, nVidia 8400GS, Delta DPS-650BB 650W PSU, Windows 7 ProComment
-
Re: Received by error
right now its still sitting on my desk.
on another note does anyone know what or whare i can get a <ph>3w1r2k?
My Computer.
AMD APU A4-3300 2.5ghz 1mb cache
Motherboard GigaByte GA-A75M-S2V
Kingston HyperX Blue DDR3 8GB (2x4GB)
SB Audigy 2 ZS [B800] Sound Card
500GB WD Caviar® Blue™
1 Terabyte WD Caviar® Black™
2 Terabyte WD Caviar® Black™Comment
-
Re: Received by error
Is that a fusible resistor - picture of it ?
Forget that it is your other post - dont know why you did not just ask there?Last edited by selldoor; 12-08-2012, 05:02 AM.Please upload pictures using attachment function when ask for help on the repair
http://www.badcaps.net/forum/showthread.php?t=39740Comment
-
Re: Received by error
i hadnt created that thread yet at the time i asked the question.My Computer.
AMD APU A4-3300 2.5ghz 1mb cache
Motherboard GigaByte GA-A75M-S2V
Kingston HyperX Blue DDR3 8GB (2x4GB)
SB Audigy 2 ZS [B800] Sound Card
500GB WD Caviar® Blue™
1 Terabyte WD Caviar® Black™
2 Terabyte WD Caviar® Black™Comment
-
Hi all!
HISENSE 65E7KQ PRO
RSAG7.820.13512 - chassis
MT9618BAATAB - cpu
RSAG7.820.12059 - power
HD650Y3U77 - panel
KLM8G1GETF - emmc
The TV does not turn on, the standby indicator is on. All voltages are present.
Emms is dead. Not readable, not detected.
Replaced emmc.
But with another dump there is no launch
Terminal log
UART
<
AC_ON
RPMB key is not yet programmed
HASH1_VERSION=0x00000000 64bit
E-B
FDE enabled
layout pattern onebin by SAR7,0...06-01-2025, 02:11 AM -
Hello Sharp TV experts
Our Sharp LC-80LE642U displays one short one long flash error code which is a backlight error. I went into service mode and there were 8 lamp error counts recorded. I reset the count to 0 and did a reset. The last monitor error cause was 16 B00014639:12. 16 is the code for backlight error. I tried to power the tv up but went back into error mode.
> I checked voltages on the power supply board and they all check out .. including 3.28 volts at the error pin.
> There is power to the cpu and T-CONN and no faults found there. The cpu has a flashing...01-24-2025, 11:51 PM -
Hi,
I have a 2014 vintage Philips 60PFL8708S/12 that suddenly died in the middle of the kids watching a show.
The relevant service manual for the chassis is available here.
The TV no longer powers on, and leaving it powered on for a few minutes results in the layer-1 error with 2 blinks.
When I short the SDM to ground I get the layer-2 error code 53.
The inside of the TV has no damaged components and no swollen capacitors.
In SDM-mode when all the power rails are left on despite entering the protection mode, I tracked down and measured... -
Macbook Pro 2019 T2
iCloud OFF
MDM unlocked by changing Serial Number
worked fine but after latest update see (There was an error activating your device. Please try again).
Erased and boot in internet recovery, same error.
changed to original serial number (iCloud OFF & MDM ON), same error.
tested with others serial number, same error.
tested (CMD+R), (Option+CMD+R), (Shift+Option+CMD+R), same error
Revived and restored by Apple Configurator and same error.
Any help ? -
Hello everyone, next I have the following problem with the Sumsour 8586D 110v dual station I bought it a year ago and it worked wonderfully, now it presents the H-E error on the soldering iron side, the hot air side works correctly..... I disassembled the soldering iron head because the manual tells me that this error is due to ceramic resistance problems, in effect, I measured it and it is open, I bought a new one that is working verified in a soldering iron and nothing.... The same error continues, I proceeded to open the station and check visually, I found a totally damaged 1R00 surface mount...
Comment