I have some caps that I am having a hard time identifying. Can anyone assist me? Thank you for your expertise. it is a cylindrical cap about 8mm dia. with 3 lines of text top line is EP middle line is 47-16 then a line across and bottom line is V1
-
-
-
Re: Cap Identification
Here is a pic.Attached FilesComment
-
-
Comment
-
Re: Cap Identification
Nothing, just manufacturers name. Can you take a guess as to what the board coating is? Manufactured in the 80s.Comment
-
Re: Cap Identification
probably 47uf and 16v
looking at what its in i think it needs to be 105' temp rated.
so maybe use rubycon YXFComment
-
Re: Cap Identification
Thank you very much, It is a cruise control unit. Appreciate the helpComment
-
PeteS in CA
Power Supplies should be boring: No loud noises, no bright flashes, and no bad smells.
****************************
To kill personal responsibility, initiative or success, punish it by taxing it. To encourage irresponsibility, improvidence, dependence and failure, reward it by subsidizing it.
****************************Comment
-
Re: Cap Identification
Thank you PeteS. I appreciate the helpComment
-
Hi to all,
I was given this TV, an entry-level 4K 50" set. Some have criticized its lack of contrast and relatively poor colour rendering, but for my needs, it's very decent.
I reset everything to factory settings, but this line keeps on fading in and out when watching a streaming channel from the Tizen firmware. Interestingly, it only happens when TV is warm, after about 1h45 of it being turned on.
Watching a movie from an external source doesn't trigger the line as easily (needs 2 hours), and from a normal viewing distance, is hardly noticeable. It...01-10-2024, 01:26 AM -
Hi all.
I have a Kogan 65' LCD Panel with a thin blue vertical line (top to bottom) on left hand side of panel.
The line just happens to coincide with the end of COF and start of the next COF (attached).
The line is permanent no matter what I've tried. I've tried pressure testing the panel (top to bottom) and all over, I didn't notice any difference with the line, either temporary or semi-permanent.
Also tried unplugging all flex cables, cleaned with isopropyl then re-inserting to no avail - line remains.
Hoping to fix... -
hello,
there is an asus gtx1650 which displays fine in windows but if i run a benchmark test it displays artifacts and the driver crashes after a second or two.
I changed pads and thermal paste.
I run mats test but it is reporting 0 errors.
I then tried to run the mods version 400.271_1650 test, it first ran and stopped with a 'breakpoints limit reached after 5 retries' error and the fans went full speed.
After a reboot, I tried to run the test again, but now the test fails and says "ERROR: Couldn't clear GPU's interrupt...02-09-2022, 03:22 PM -
I have a 2DS that I am working on that has a problem reading SD cards. It knows that card is in the slot (which, means the detect pin is working anyway) but it says it can’t read the card.
Here is what I have done so far:
-Tried SD card in another 2DS and on PC, works great.
-Tried piggybacking another SD card slot (just so I didn’t have to take the other one off), same issue.
-Compared voltage drop readings from a working 2DS to the faulty one. All reads are very close except one, the 7th pin from the left, with the pins closest to you, which I believe... -
Hi Everyone,
I have brought to you a strange problem display maybe you have some ideas how it can be fixed or what could cause such a problem.
Display Type: B173ZAN01.1
MANUFACTURER: AU Optrinics
H/W:0A F/W:1
Changed the cable and tried to bend, push the back f the screen and both problem persists, nothing changes.
There is no any sign that the back of the screen was under pressure, or has moving cables.
PROBLEM 1:. Red spots / area in the screen
MORE INFO: If i gently press above the problematic area then it disappears until...04-10-2024, 12:22 PM
Comment